background image

128-6528

1 of 28

Model PRO-9800

Installation Manual

RY

SELECTABLE FEATURES

Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code.  Be

certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.

RF Programmable Features :

Feature Selection

1 Chirp

2 Chirps

3 Chirps

4 Chirps

Default

1st DoorL/UL

1 Sec.

3.5  Sec.

1 Sec L, Dbl. U/L

1 Sec.

2nd Accy Lock

Auto Lock On

Auto Lock Off

Auto Lock Off

3rd Accy. UL

Auto UL Dr.

Auto UL All

Auto UL Off

Auto UL Off

4th Headlights

On Arm

On Disarm

On Both

Off

Both

5th Passive Locks

Passive

Active

Active

6th Passive/Active Arm

Passive Arm

Active Arm

Active Arm

7th Black/Blue (Aux O/P)

Single Pulse

As Feature #1

Single

8th Siren/Horn

Siren/Horn

Siren Only

Horn Only

Siren/Horn

9th Horn Chirp

10mS

16mS

30mS

16mS

10th Override Method

Custom Code

Valet

Valet

11th Two Step Unlock

On

Off

Off

12th Chirp Delete From Tx

On

Off

Off

To program these selectable features;

Action

System Response

Turn ignition on

No  response

Press and release the valet switch 3 times

1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off

Short chirp, then long chirp

First

Then turn the ignition back On

1 chirp = 1 second door locks

Press transmitter Lock button to change

2 chirps = 3.5 second door locks

Press transmitter Lock button to change

3 chirps = 1 sec. lock, dbl 1 sec. unlock

o r

Second

Press and release the valet switch

2 chirps = auto locks off

Press transmitter Lock button to change

1 chirp = auto locks on

o r

Third

Press  and release the valet switch

3 chirps = auto unlock off

Press transmitter Lock button to change

1 chirp = auto unlock drivers door only

Press transmitter Lock button to change

2 chirps = auto unlock all doors

o r

Fourth

Press and release the valet switch

3 chirps = headlight output when arming and disarming

Press transmitter Lock button to change

4 chirps = headlight output off

Press transmitter Lock button to change

1 chirp = headlight output when arming

Press transmitter Lock button to change

2 chirps = headlight output when disarming

o r

Fifth

Press and release the valet switch

2 chirps = active locks

Press transmitter Lock button to change

1 chirp = passive locks

o r

Sixth

Press and release the valet switch

2 chirps = active arming

Press transmitter Lock button to change

1 chirp = passive arming

o r

Seventh

Press and release the valet switch

2 chirps = as feature #1

Press transmitter Lock button to change

1 chirp = single pulse

Summary of Contents for PRO-9800





























Reviews: