Prusa Research Original Prusa SL1 Manual Download

Page: 1 / 92

Table of Contents

1. Introduction

......................................................................................................................

Step 1 - All the required tools are included

................................................................

Step 2 - Boxes and bags are labelled

..........................................................................

Step 3 - Use labels for reference

.................................................................................

Step 4 - Spare bag

..........................................................................................................

Step 5 - View high resolution images

.........................................................................

Step 6 - We are here for you!

........................................................................................

Step 7 - Unpacking the SL1 kit

.....................................................................................

Step 8 - Important: Electronics protection

................................................................

Step 9 - Regular rewards are crucial!

........................................................................

Step 10 - How to successfully finish the assembly

.................................................

2. Base & Tower

.................................................................................................................

Step 1 - Tools and bags for this chapter

...................................................................

Step 2 - Preparing parts from the package

..............................................................

Step 3 - Preparing parts from the package

..............................................................

Step 4 - Tower and PSU parts preparation

..............................................................

Step 5 - Arranging the back plate

..............................................................................

Step 6 - Connecting the tower

...................................................................................

Step 7 - Connecting the tower

....................................................................................

Step 8 - Connecting the SL1 PSU

..............................................................................

Step 9 - Tower and PSU parts preparation

..............................................................

Step 10 - Mounting the bottom plate

........................................................................

Step 11 - Mounting the supports

................................................................................

Step 12 - Mounting the adjustable feet

.....................................................................

Step 13 - Preparing PSU cables

.................................................................................

Step 14 - Connecting the cables

................................................................................

Step 15 - Preparing the tilt motor parts

...................................................................

Step 16 - Preparing the tilt motor parts

....................................................................

Step 17 - The tilt motor assembly

..............................................................................

Step 18 - The tilt motor assembly

..............................................................................

Step 19 - The tilt motor assembly

.............................................................................

Step 20 - Preparing the reflector

...............................................................................

Step 21 - Mounting the reflector

................................................................................

Step 22 - Right blower fan parts preparation

.........................................................

Step 23 - Right blower fan parts preparation

.........................................................

Step 24 - Blower fan gasket

.......................................................................................

Step 25 - Fan assembly (new version)

.....................................................................

Step 26 - Fan assembly (old version)

.......................................................................

Step 27 - Blower assembly

.........................................................................................

Step 28 - Mounting the fan assembly

......................................................................

Step 29 - Tilt preassembly parts preparation

.........................................................

Step 30 - Resin sensor cable assembly

....................................................................

Step 31 - Tilt parts preparation

..................................................................................

Step 32 - Mounting the tilt assembly

.......................................................................

Step 33 - Optical sensor calibration

.........................................................................

Step 34 - Haribo time!

.................................................................................................

Step 35 - Final check

...................................................................................................

3. Covers & Platform

.......................................................................................................

Step 1 - Tools and bags for this chapter

...................................................................

Step 2 - Preparing parts from the package

.............................................................

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands