REQUIRED FREE DISTANCE BELOW WORKING LEVEL FOR WORKER PROTECTED WITH ENERGY ABSORBER WITH LANYARD
!
free distance below working surface must be 6,2 m (see drawing no.1)
!
drawings no.2 and no. 3 show free distance below working surface depending on location of Structural Anchor Point.
The energy absorber with lanyard
is a component of personal fall arrest equipment and complies with EN355.
Fall arrest system consisted of energy absorber with lanyard
,
attached to the full body harness (complied with EN 361) and connected to the structural
anchor point (complied with EN 795) can be used as a basic personal protective equipment against falls from a height.
Caution: The total length of the energy absorber with lanyard including terminations and connectors shall not exceed 2 m.
(e.g. connector plus lanyard plus energy absorber plus connector)
~1
,5 m
~1
,5 m
~1
,5 m
~4,7 m
~3,2 m
~6,2 m
2
1
3
3,5 m - free fall
Structural Anchor Point
min. 12 kN
1,2 m - ultimate
elongation
of the energy
absorber
0,2 m - displacement
of the back attaching buckle
+1 m - security
1,8 m - man height
2 m - free fall
Structural Anchor Point
min. 12 kN
1,2 m - ultimate
elongation
of the energy
absorber
0,2 m - displacement
of the back attaching buckle
1,8 m - man height
+1 m - security
Structural Anchor Point
min. 12 kN
0,5 m - free fall
1,2 m - ultimate
elongation
of the energy
absorber
0,2 m - displacement
of the back attaching buckle
1,8 m - man height
+1 m - security
EN 355:2002
Instruction Manual
Read carefully
the manual
before use
the equipment
ENERGY ABSORBER
w i t h l a n y a r d
ATTENTION!
The energy absorbers can be equipped only with certified (according to EN362) connectors.
Ref.: BW 200/LB101
EN 355:2002
ENERGY ABSORBER WITH LANYARD LB101
Serial
number:
0000001
Date
of manufacture:
03.2017
ABM / LB101
CONTENT OF THE DEVICE IDENTITY LABEL
Energy absorber is made of 32 mm wide
webbing. Absorber is equipped with attachment loops on the endings. One of the loops is connected
to the lanyard. The body of the absorber is protected by a special jacket made of a shrinkable, polyethylene tube. The lanyard can be made of:
-
10,5 mm polyester kernmantle rope eneded with sewn loops (ABM/LB101, ABM/LB102).
-
ø
12 mm polyester kernmantle rope eneded with sewn loops (ABM/LB121, ABM/LB122).
-
ø
14 mm polyester kernmantle rope eneded with sewn loops
(ABM/LB141).
-
ø
12 mm polyester kernmantle rope eneded with sewn loops. One loop is adjustable by steel adjustment buckle (ABM/LB100, ABM/2LB100).
- tubular polyamide webbing with elastic core inside. The endings of the lanyard are sewn making the attachment loops (ABM/ LE101, ABM/2 LE101).
- 30 mm polyester webbing eneded with sewn loops equipped with thimbles
(ABM-T, ABM-2T)
polyamide
ø
CONSTRUCTION
the maximum length of the energy absorber with lanyard can’t exceed 2 m
A
B
C
D
E
F
G
H
I
A. type of the device
B. marking of the model of energy absorber
C. reference number of the device
D. CE marking with identity number of the notified body
controlling manufacturing of the equipment
(the article 11)
E. European standards (number/year)
F. month/year of the device manufacture
G.
H. caution: read the manual
I. marking of the manufacturer or distributor
number of the manufacturing series
1. absorber's attachment loop ; 2. energy absorber ; 3. lanyard ; 4. lanya
5. thimble ; 6. lanyard's seam;
7. adjustment buckle ;
8. identity label.
rd's attachment loop ;
Ref. BW 200/LB 141
ABM/LB141
Ref. BW 200/LB 121
ABM/LB121
Ref. BW 200/LB 101
ABM/LB101
1
2
3
4
6
6
8
1
2
3
4
6
6
8
7
Ref. BW 200/LB 100
ABM/LB100
Ref. BW 200/LE 101
ABM/LE101
1
2
8
5
5
3
4
6
6
1
2
6
8
3
5
4
6
1
2
6
8
3
5
4
6
6
1
2
8
4
6
3
6
Ref. BW 200/LB 102
ABM/LB102
Ref. BW 200/2 LB 100
ABM/2LB100
Ref. BW 200/2 LE 101
ABM/2LE101
1
1
2
8
2
ABM-T
8
ABM-2T
6
6
Ref. BW 700
3
Ref. BW 800
4
6 5
3
4
5
6
Ref. BW 200/LB 122
ABM/LB122
IDENTITY CARD
SERIAL NUMBER
USER NAME
DATE OF MANUF.
DATE OF PUTTING
INTO OPERATION
DATE OF PURCHASE
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED. THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A
COMPETENT PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT. ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF
EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON. THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT
UTILIZATION.
DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD. ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.
MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
PERIODIC EXAMINATION AND REPAIR HISTORY
DATE
REASON FOR
ENTRY PERIODIC EXAMINATION
OR REPAIR
DEFECTS NOTED,
REPAIRS CARRIED OUT
AND OTHER REVELANT INFORMATIONS
NAME AND SIGNATURE
OF COMPETENT PERSON
PERIODIC
EXAMINATION
NEXT DUE DATE
1
2
3
4
6
Periodic inspections
The device must be inspected at least once every 12 months from the date of first use.
Periodic inspections must only be carried out by a competent person who has the knowledge and training required for personal protective equipment
periodic inspections. Depending upon the type and environment of work, inspections may be needed to be carried out more frequently than once every
12 months. Every periodic inspection must be recorded in the Identity Card of the equipment.
Maximum lifespan of the equipment
The maximum lifespan of the energy absorber with lanyard is 10 years from the date of manufacture.
The energy absorber with lanyard must be withdrawn from use immediately and destroyed when it has been used to arrest a fall or it fails to pass inspection or
there are any doubt as to its reliability.
ATTENTION:
The lifetime of the device depends on the intensity of usage and the environment of use. Using the device in rough environment, marine
environment, contact with sharp edges, exposure to extreme temperatures or agressive substances, etc. can lead to the wthdrawal from use even after one
use.
PROTEKT
93-403 LODZ, ul. Starorudzka 9, POLAND,
TEL: (48 42) 680 20 83, FAX: (48 42) 680 20 93
www.protekt.com.pl
Notified body, at which the European certification was Iissued and which
supervises
the production of the equipment:
APAVE SUDEUROPE SAS - 8 rue Jean-Jacques Vernazza - Z.A.C. Saumaty-Séon
CS-60193 – 13322 MARSEILLE Cedex 16, France - No. 0082
