V1.0
8093650
Please read and understand all instructions before use. Retain this manual for future reference.
SPECIFICATIONS
Load Capacity
50 lb
Lift Height
4 ft
Rope Length
47.9 ft (14.6 m)
Rope Diameter
5/32 in.
Material
Polypropylene and Carbon Steel
SAFETY
WARNING! Read and understand all instructions before
using this tool. The operator must follow basic
precautions to reduce the risk of personal injury and/or
damage to the equipment.
Keep this manual for safety warnings, precautions, operating
or inspection and maintenance instructions.
1.
Use the correct tool for the job. This tool was designed
for a specific function. Do not modify or alter this tool or
use it for an unintended purpose.
2. Operate in a safe work environment.
3. Control the tool, personal movement and the work
environment to avoid personal injury or damage to tool.
4. Do not operate any tool when tired or under the
influence of drugs, alcohol or medications.
5. Always wear impact safety goggles that provide front
and side protection for the eyes. Eye protection
equipment should comply with CSA Z94.3-07 or ANSI
Z87.1 standards based on the type of work performed.
6. Avoid wearing clothes or jewelry that can become
entangled with the moving parts of a tool. Keep long hair
covered or bound.
UNPACKING
WARNING! Do not operate the tool if any part is missing.
Replace the missing part before operating. Failure to do
so could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and
inspect for damage. Make sure that all items in the contents
are included.
Contents: • Pulley Brackets (2) • Pulley Hook (2)
• Rope • Mounting Screws
• Cleat
ASSEMBLY/INSTALLATION
Refer to Figure 1 during assembly.
1.
Mount the bike lift directly to a ceiling joist capable of
supporting the bicycle’s weight.
a. Attach a wood beam across two joists if you wish to
mount the bike lift at a different angle.
2. Measure the distance between the handlebars and the rear
of the seat. Transfer this measurement to the joist or wood
beam, leaving enough space for the wheel.
3. Push the rope through the last opening in the single pulley
bracket. Tie a double knot in the rope to prevent it from
slipping out under load.
4. Mount the single pulley bracket to the joist (see Fig. 1). The
measurement mark is just behind the pulley. Secure with
three screws through the remaining center holes.
5. Mount the double pulley so the front measurement mark is
between the pulleys and the rope lock is at the front. Attach
with three screws through the center holes.
6. Orient the first pulley hook so the tines will hook under the
seat. Thread the rope through hook pulley, then up and
through the mounted pulley.
7. Pull the rope across to the rear pulley on the front pulley
bracket and thread it through from back to front.
8. Orient the second pulley hook to face backwards towards the
first pulley hook. Thread the rope through the hook pulley.
Thread through the front pulley, then through the rope lock.
9. Let the rope slide out of your hand. The rope lock should
swing upward and engage.
10. Mount the rope cleat to a suitable surface with two screws.
11. Check the rope and remove any twists that may have
formed during
installation.
12. Wrap the excess
rope around the
cleat. Do not cut
the rope as you
will need the
excess to raise and
lower the bicycle.
OPERATION
1.
Pull the rope rearward to disengage the rope lock. Pull each
pulley hook down while keeping tension on the rope.
2. Position a pulley hook under the seat and the other under
the handlebars. Pull the rope to raise the bike.
3. Pull the rope forward to engage the rope lock. Wrap the
remainder of the rope around the cleat.
4. Lower the bike by pulling the rope rearward and keeping
tension on it while lowering the bike. The rope lock will
engage if tension is released (intentional or accidental).
5. Remove the pulley hooks and raise the pulley hooks to keep
them out of the way.
Fig. 1
