background image

SmartStuff SmartBox

 + Panel Sensor

Item Number: 

SMBOXPLBT

WARNING

WARNING: DANGER–RISK OF SHOCK–

DISCONNECT POWER BEFORE INSTALLATION!

NOTE:

 This device is suitable for damp 

locations only.

 

 This product is used to control lighting luminaires with 

 

  0-10V dim to off drivers/ballast. 

 •

 This product must be installed in accordance with local 

 

  and national electrical codes. Please consult with a 

 

  qualified electrician before installation.

NOTE:

 Please read the instructions before 

proceeding with the installation.

 

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, 

including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. 

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in an installation. If this equipment 

does cause harmful interference to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the interference by one or more of the 

following measures:  

—Reorient or relocate the receiving antenna.  

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  

—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 

This equipment should be installed and operated with minimum distance 8 inches between the radiator & your body.

Specifications

Input Voltage

 • 

120 – 277VAC @ 15mA

Input Line Frequency

 • 

50/60Hz

Maximum Power

 • 

1W

Output Voltage

 • 

0-10VDC

Operating Temperature

 • 

-23°F to 113°F

Humidity

 • 

<80% RH

Radio Protocol

 • 

Bluetooth Signal Mesh

Communication Range

 • 

150 ft / 46 m

Sm Panel Sensor Setting:

Microwave Maximum Height........ 10 feet / 3m
Microwave Maximum Diameter.... 33 feet / 10m
PIR Maximum Height .................... 10 feet / 3m
PIR Maximum Diameter............. 16 feet / 5.0m
Sensor Detection Angle.............................360°
Hold Time............................. 1 min. –1092 min.
Daylight Sensor Setpoint ............... 0 – 300 lux

Regulatory Approvals

• ETL Listed
• Contains FCC ID: NIR-MESH8269
• Contains IC: 9486A-MESH8269
• Conforms to UL 8750
• Certified to CSA C22.2 No. 250.13

Installation of the Sm Panel Sensor

Check the label on 

the SmartBox for correct 

orientation and Install 

as shown. The junction 

box needs a 1/2" knock-

out for the Sm 

Panel Sensor to fit 

securely. Use double-

sided tape if needed. 

½"

Switch between Microwave Sensor and PIR Sensor.

PIR sensor

Microwave sensor

Electrical Connections

Make the electrical 

connections as shown. 

Sm 

Panel Sensor

Luminaire Driver

L N

L

DIM+

DIM-

N

black(18AWG)

purple

(22AWG)

gray

(22AWG)

white(18AWG)

(120-277v)

Maintain a minimum distance of 4.92 ft / 1.5m between:
• A window and the Sm Panel Sensor.
• The Sm Panel Sensor and other TCP SmartStuff products with a Microwave Sensor.
Make sure no light is reflected in the direction of the Sm Panel Sensor

LIMITED WARRANTY: This product is warranted for a period of 5 

YEARS* from date of original purchase against defects in materials 

and workmanship. If this product should fail to operate due to 

defects in material or workmanship, simply call 1-800-771-9335 within 

5 YEARS of purchase. This product will be repaired or replaced, at 

TCP’s option. This warranty is expressly limited to repair or replace-

ment of the product. This warranty gives the consumer specific legal 

rights, which vary from state to state. WARRANTY IS VOID IF PROD-

UCT IS NOT USED FOR THE PURPOSE FOR WHICH THIS PRODUCT 

IS MANUFACTURED.

TCP SmartStuff App

The TCP SmartStuff App is used to configure the Bluetooth® 

Signal Mesh and TCP SmartStuff devices. 

Download the TCP SmartStuff App using the following options: 

•  Download the SmartStuff App from the 

  Apple App Store or Google Play Store       

•  Use the QR Codes here:

Instructions for configuring TCP Smart App and SmartStuff 

devices are at https://www.tcpi.com/tcp-smartstuff/

Reviews: