Philips SC16C2550 Manual Download | Manualshive

Page: 1 / 46

background image

SC16C2550

Dual UART with 16 bytes of transmit and receive FIFOs
and infrared (IrDA) encoder/decoder

Rev. 03 — 19 June 2003

Product data

1.

Description

The SC16C2550 is a 2 channel Universal Asynchronous Receiver and Transmitter
(UART) used for serial data communications. Its principal function is to convert
parallel data into serial data and vice versa. The UART can handle serial data rates
up to 5 Mbits/s.

The SC16C2550 is pin compatible with the ST16C2550. It will power-up to be
functionally equivalent to the 16C2450. The SC16C2550 provides enhanced UART
functions with 16-byte FIFOs, modem control interface, DMA mode data transfer. The
DMA mode data transfer is controlled by the FIFO trigger levels and the TXRDY and
RXRDY signals. On-board status registers provide the user with error indications and
operational status. System interrupts and modem control features may be tailored by
software to meet specific user requirements. An internal loop-back capability allows
on-board diagnostics. Independent programmable baud rate generators are provided
to select transmit and receive baud rates.

The SC16C2550 operates at 5 V, 3.3 V and 2.5 V and the Industrial temperature
range, and is available in plastic PLCC44, LQFP48 and DIP40 packages.

2.

Features

■

2 channel UART

■

5 V, 3.3 V and 2.5 V operation

■

Industrial temperature range

■

Pin and functionally compatible to 16C2450 and software compatible with
INS8250, SC16C550

■

Up to 5 Mbits/s data rate at 5 V and 3.3 V, and 3 Mbits/s at 2.5 V

■

16 byte transmit FIFO to reduce the bandwidth requirement of the external CPU

■

16 byte receive FIFO with error flags to reduce the bandwidth requirement of the
external CPU

■

Independent transmit and receive UART control

■

Four selectable Receive FIFO interrupt trigger levels

■

Automatic software/hardware flow control

■

Programmable Xon/Xoff characters

■

Software selectable Baud Rate Generator

■

Sleep mode

■

Standard asynchronous error and framing bits (Start, Stop, and Parity Overrun
Break)

■

Transmit, Receive, Line Status, and Data Set interrupts independently controlled

1
2
3
...
»

Summary of Contents for SC16C2550















































Reviews:

No comments

Related manuals for SC16C2550

Brand: K&K Sound Pages: 6

Brand: Paul Wegener Pages: 8

STINGER2 433TSD22V2

Brand: Transmitter Solutions Pages: 2

Brand: DeviceGate Technology Pages: 17

FT DX 9000 - CAT OPERATION REFERENCE BOOK

Brand: Yaesu Pages: 20

Brand: E+E Elektronik Pages: 48

Quantec QT412RXA

Brand: C-TEC Pages: 2

RV-100 RealVision 3D

Brand: Raymarine Pages: 2

Brand: Team Electronic Pages: 60

Brand: C4Line Pages: 2

Brand: Midland Pages: 20

SlingStudio CameraLink

Brand: Sling Media Pages: 4

Brand: Williams Sound Pages: 16

Brand: Baumer Pages: 10

Brand: Equitel Pages: 10

Brand: Viatran Pages: 5

Brand: Viatran Pages: 4

Brand: PR electronic Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands