background image

1

SNE2040G-P and SNE2040G-S

4-Port Network Extenders Installation Instructions

Document Number SNE2-A2-GN12-00

September 2004

Contents

Software and Firmware License Agreement

.................................................

1

Product Documentation Online

.....................................................................

3

Warranty, Sales, Service, and Training Information

......................................

3

Package Contents

........................................................................................

3

Connecting to Power

....................................................................................

4

Switchpack Configuration (SNE2040G-P)

....................................................

5

Connecting the SHDSL Lines

.......................................................................

6

SHDSL RJ45 Connector Pinouts

..................................................................

7

Connecting the Ethernet Line

.......................................................................

8

10/100 Ethernet RJ45 Pinouts

......................................................................

8

LED Indicators

..............................................................................................

9

EMI Notices

.................................................................................................. 11

Important Safety Instructions

........................................................................ 11

Software and Firmware License Agreement 

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.

Summary of Contents for SNE2040G-P













Reviews: