Panduit CT-2002CH Manual Download

Page: 1 / 7

CT-2002CH

PA29258A01

Rev. 00 6-2018

REMOTE CRIMP HEAD HYDRAULIC COMPRESSION TOOL

TABLE OF CONTENTS

SYSTEM SPECIFICATIONS ..................................................................................................................... 1

OPTIONAL ACCESSORIES

(sold separately)

.......................................................................................... 1

PRECAUTIONS AND GENERAL GUIDELINES ........................................................................................ 2

DIE SELECTION ....................................................................................................................................... 4

DIE INSTALLATION .................................................................................................................................. 4

TOOL OPERATION .................................................................................................................................. 5

MAINTENANCE ........................................................................................................................................ 6

PERIODIC MAINTENANCE ................................................................................................................ 6

CLEANING AND LUBRICATION OF TOOL HEAD .............................................................................. 6

VISUAL INSPECTION ......................................................................................................................... 6

FORCE INSPECTION / CALIBRATION ............................................................................................... 6

CONTACT INFORMATION ....................................................................................................................... 6

Email:

[email protected]

EU Website:

www.panduit.com/emea

EU Email:

emeatoolservicecenter

@panduit.com

www.panduit.com

Technical Support

Tel: 1-800-777-3300

Panduit Europe • EMEA Service Center

Almelo, Netherlands

Tel: +31 546 580 452 • Fax: +31 546 580 441

Summary of Contents for CT-2002CH








Search results

Summary of Contents for CT-2002CH

Reviews:

Related manuals for CT-2002CH

Brands by name

Popular brands

Panduit CT-2002CH, Manual

Search results

Summary of Contents for CT-2002CH

Reviews:

Related manuals for CT-2002CH

Brands by name

Popular brands