background image

Pandora would like to thank you for choosing our

DXL 0110L service and security system

Pandora is a brand of Russian Experimental Engineering Factory, a full 

production cycle electronics R&D facility. We design and produce car service-

security systems for more than 10 years and have reached a considerable 

success on Russian and CIS markets – biggest security system markets in the 

world. Our systems are made to withstand severe weather conditions and 

criminal situation of northern Eurasia.

Pandora DXL 0110L is a car service-security system, built for cars with on-board 

voltage of 12V. It is a complex engineering solution which includes car security 

system, algorithmic security that detects various events and immobilizer with 

possible RF tags, all controlled from your OEM key remote. This system is designed 

to be all-in-one car security solution and requires no additional modules. 

It is essential for systems functioning that you read and understand 

instructions in this manual. Note that all radio devices are subject to 

interference, which could affect proper performance.

This device has limited external factors resistance. It should not be subjected to water beyond occasional splatter, or operated in

temperatures outside -40 to +80° C range

IMPORTANT! Note that this manual describes remote and manual functions for 
the most part. Functionality of the system is vast and would require a book-sized 
manual to fully describe. Instead we use a handy software named AlarmStudio that 
functions as both programming tool and an extended installation & functionality 
manual. It requires Window sand can be downloaded at pandorainfo.com

Product is in conformity with Electromagnetic Compatibility

Directive EMC 2004/108/EC and R&TTE Directive 1999/5/EC

WARNING! IT IS STRONGLY ADVISED TO HAVE PROFES-

SIONAL CAR MECHANIC INSTALLING THE SYSTEM. CERTI-

FIED INSTALLERS ARE RARE OUTSIDE RUSSIA, BUT ANY CAR 

ELECTRONICS INSTALLER SHOULD BE ABLE TO INSTALL 

PANDORA DXL 0110L USING INSTALLATION SCHEME IN THIS 

MANUAL AND ALARMSTUDIO SOFTWARE. MOST FEATURES 

ARE HIGHLY DEPENDENT ON COMPETENT INSTALLATION. 

OUR SYSTEMS ARE THOROUGHLY TESTED FOR QUALITY, SO 

IF A FEATURE FAILS TO PRODUCE EXPECTED RESULTS, MOST 

LIKELY THE PROBLEM IS IN IMPROPER INSTALLATION.

Summary of Contents for DXL 0110L


















Reviews: