Panasonic NC-TWS30 Service Manual Download

Page: 1 / 20

Electric Thermo Pot

NC-TWS30

Service Manual

ORDER NO. PHAT070602C3

Speciﬁcations

Power Supply

NC-TWS30

AC 240V 50 Hz

Power Consumption

(approx.)

Rated Vale

635 W

Boiling

635 W

Capacity (approx.)

3.0L

Dimensions (approx.) (W x D x H)

22.2 cm x 29.4 cm x 31.1 cm

Weight (approx.)

2.0 kg

Thermal regulation

Thermostat

Rotating base

360° Rotatable with the power cord

Thermal fuse

157°C (2 thermal fuses)

Power cord

Section area approx. 1 mm

Length approx. 0.83 m

Hot water supply device speciﬁcations

Hot water supply method

Air pump

Current volume adjustment range

170 ml/5sec

Operation method

Push Supporting Plate

Pump-lock

Push Stopper

Additional functions: Overheating protection, Air pump, Lock Knob (Air Pump type)

WARNING

This service information is designed for experienced repair technicians only and is not designed for use by the general public.

It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.

Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service

or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.

is a violation of law.

Product Color :

Pink

Destination :

Malaysia

Panasonic

Summary of Contents for NC-TWS30





















Search results

Summary of Contents for NC-TWS30

Reviews:

Related manuals for NC-TWS30

Brands by name

Popular brands

Panasonic NC-TWS30, Service Manual

Search results

Summary of Contents for NC-TWS30

Reviews:

Related manuals for NC-TWS30

Brands by name

Popular brands