background image

Operating Instructions (Basic)

AC Servo Motor & Driver

MINAS A5E-series (A to F-frame)

Make sure to forward these Operating Instructions for safety to the final user.

• Thank you for purchasing this 

Panasonic product.

• Before operating this product, 

please read the instructions 

carefully, and save this manual for 

future use.

1. Introduction ................................. B2

On Opening the Product Package .................. B2

Check of the Driver Model .............................. B2

Check of the Motor Model............................... B3

2. Installation................................... B4

Driver .............................................................. B4

Motor ............................................................... B6

3. System Configuration and 

 Wiring ........................................... B8

Overall Wiring (Connector type) ..................... B8

Overall Wiring (Terminal block type) .................B12

Driver and List of Applicable Peripheral Equipments .... B14

Wiring of the Main Circuit (Connector type)......... B16

Wiring of the Main Circuit (Terminal block type) ... B18

Wiring method to connector ............................. B19

Wiring Diagram ............................................. B21

Wiring of connector for motor and brake ...... B23

Wiring to the Connector, X1  ......................... B24

Wiring to the Connector, X4  ......................... B25

Wiring to the Connector, X6  ......................... B27

Wiring to the Connector, X7  ......................... B28

4. Parameter .................................. B29

Outline / Setup / Connection ......................... B29

Composition of Parameters .......................... B31

5. Protective Functions ................ B32

Protective Function (What Is Error Code ?) ...... B32

6. Maintenance and Inspections .... B34

7. Conformity to EC Directives 

  and UL Standards ..................... B36

Composition of Peripheral Equipments ........ B38

8. Built-in Holding Brake .............. B43

9. Dynamic Brake.......................... B45

10. Check of the Combination of

     the Driver and the Motor ............ B46

  Incremental Specifications, 20-bit ............... B46

11. Specifications ......................... B48

After-Sale Service (Repair) .......... B50

 

page

page

<Contents>

If you are the first user of this product, please be sure to read the downloaded  

Operating Instructions (Overall) from our Web Site.

[Web address of Panasonic Corporation]

http://industrial.panasonic.com/ww/i_e/25000/motor_fa_e/motor_fa_e.html

This product image is 1.5 kW type of A5E-series.

English

IME03+B

This product is for industrial 

 

 

equipment. Don't use this 

  

 

product at general household.

Summary of Contents for MINAS A5E Series




























Reviews: