background image

© Panasonic Corporation 2018 Unauthorized copy-
ing and distribution is a violation of law.

Order Number PTD1808E01CE

Cordless Drill & Driver

Model No.

EY7451

Europe

TABLE OF CONTENTS

PAGE

Safety Precautions

-----------------------------------------------

2

2 Specifications

-----------------------------------------------------

2

2.1. EY7451 MAIN UNIT -------------------------------------- 2
2.2. MAXIMUM RECOMMENDED CAPACITIES ------- 2

Troubleshooting Guide

-----------------------------------------

3

3.1. Trial Operation (after checking 

Troubleshooting Guide.) --------------------------------- 6

Disassembly and Assembly Instructions

----------------

7

4.1. How to disassemble Plate hoot and Keyless

chuck.--------------------------------------------------------- 7

4.2. How to disassemble Main unit.------------------------- 8

Wiring Connection Diagram

---------------------------------

13

Schematic Diagram

---------------------------------------------

14

Exploded View and Replacement Parts List

-----------

15

7.1. PARTS LOCATION---------------------------------------15
7.2. REPLACEMENT PARTS LIST ------------------------16

Summary of Contents for EY7451

















Reviews: