![background image](http://html1.mh-extra.com/html/ottlite/workwell-ww10sk1/workwell-ww10sk1_quick-start-manual_1658930001.webp)
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with your new OttLite
®
product.
WARRANTY INFORMATION
This product features a 5 year limited warranty. For more information visit:
OttLiteWorkWell.com/warranty
WARNING:
To prevent electric shock, make sure the lamp is not plugged in until
all steps are complete.
NOTE: THIS UNIT IS FULLY ASSEMBLED
1.
Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
2.
Connect power adapter input (J) into connector (K) in the rear-bottom of the lamp.
3.
Plug the power adapter (L) into a standard household 120V AC outlet.
Note:
Only use with the supplied power adapter to avoid damage or fire.
4.
Touch the ON/OFF button (B) to power ON or power OFF the lamp.
5.
Brightness can be adjusted by sliding a finger over the dimmer panel (C).
NOTE:
If dimmer function was employed prior to turning “OFF” lamp, the lamp
will return to lamp setting last employed unless disconnected from adapter.
6.
Wireless Charger for Qi-certified devices (D) is located in the center of the base
(A). See
Wireless Charging Instructions
section for details.
7.
To position the light adjust the arm (F) and/or adjust the the shade (G) until desired
position is achieved. Please hold the lamp base (A) while adjusting the lamp. Take
care not to overextend the lamp to avoid unbalancing it and damage. Please refer
to diagrams for lamp maximum adjustment range.
WIRELESS CHARGING INSTRUCTIONS:
Wireless charging requires a Qi-certified device. To determine if your device is
Qi-certified, please visit the Wireless Power Consortium website.
To wirelessly charge a device, perform the following:
• Check for the LED indicator light (E) below wireless charger (D) to be
RED
. This
signifies a device can be charged.
• Place the device, which supports Qi wireless charging standard, face up on the
middle of the Qi wireless charging icon (D).
• LED Indicator light (E) will turn
BLUE
noting charging mode is active.
• When the device is centered on the Qi wireless charging icon (D), a
BLUE
light will indicate the device is charging properly.
NOTE:
If a
RED
light is visible,
this indicates the device is not charging and needs to be properly centered.
• Check the charge level on your device periodically to determine when device is
fully charged.
NOTE:
Lamp
DOES NOT
provide any indication of when device is
fully charged
.
CAUTION!
DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL
AND PART OF THE PROCESS. CHARGING TIME VARIES BY DEVICE MODEL.
SAFETY WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS
1.
Turn lamp off and
WAIT UNTIL LAMP HEAD (G) IS COOL
before handling.
2.
The LED panel (H) might get hot after several hours of continuous use
DO NOT
place your hands directly on LED light panel.
3.
Never use with an extension cord unless the plug can be fully inserted into the
receptacles in the extension cord.
4.
Do not alter the plug.
5.
The lamp head included with this unit cannot be replaced by the consumer.
6.
INDOOR USE ONLY.
NOTE:
The important safety instructions appearing in this instruction sheet are not meant
to cover all possible conditions and situations that may occur. It must be understood that
common sense, caution, and care must be used with any electrical product.
CAUTION!
IF THE ExTERNAL FLExIBLE CABLE OR CORD OF THIS LUMINAIRE IS
DAMAGED, IT SHALL BE ExCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE
AGENT OR A SIMILAR qUALIFIED PERSON IN ORDER TO AVOID A HAzARD. INDOOR USE ONLY.
CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN
THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC/IC RF Radiation Exposure Statement Caution:
To maintain compliance with
the FCC’s RF exposure guidelines, place the product at least 10cm from nearby persons.
IC CANAdA
This device contains licence-exempt transmitter(s)/receiver that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
CAN RSS-216/CNR-216
CAN ICES-005 (B)/NMB-005 (B)
CAUTION:
Any change or modification to product not expressly recognized by
OttLite Technologies voids OttLite’s responsibility for proper function of product.
AC/DC ADAPTER SPECIFICATION:
Input: AC 100-240V, 50/60 Hz, 1A
Output: 12V DC, 2500mA with a Male DC Plug
Qi CHARGER SPECIFICATION:
Output: 5V, 1A or 5 watts
THIS LAMP CONTAINS a 5V, 2,1A USB output port (M) located on the bottom rear of
lamp. USB port can charge items such as tablets, cellular phones, etc.
The “Qi” symbol is a trademark of the Wireless Power Consortium
ACCESSORY:
2-in-1 Lightning and Micro USB cable included is for charging
purposes only.
NOT FOR DATA TRANSFER.
English
The Elevate LED Desk Lamp with Wireless Charging
H
C
The Elevate LED Desk Lamp with Wireless Charging
WW10SK1
MA70M
INS180453
REV018119
B
D
G
J
M
K
L
F
E
30°
30°
90°
45°
90°
0°
A