OSRAM GmbH Costumer Service Center
Albert-Schweitzer-Str.64, 81735 Munich
Germany
Tel :+49 (0) 1803 677 - 200
Fax. :+49 (0) 1803 677 - 202
www.osram.com
www.osram.de
Operating instructions
III / 2006
Radio Remote Control
Touch DIM RMC
page 2
OSRAM - Operating instructions: TOUCH DIM RMC
General
Table of contents
General
Installation
Start-up
Annex
Application and function ............................................. 2
Safety and installation instructions............................. 2
Design and dimensions.............................................. 3
Learning the handheld transmitters ........................... 4
Unlearning / cancelling transmitters........................... 4
Operation.................................................................... 5
Notes on radio operation............................................ 6
Troubleshooting.......................................................... 7
Technical data ............................................................ 8
Application and function
The TOUCH DIM RMC handheld transmitter enables a wireless remote control of up to 4 luminaire
groups equipped with OSRAM ECG with Touch DIM function. The Touch DIM RC module receives
radio telegrams from radio transmitters and converts them into Touch DIM signals. The transmitters
are based on induction technology and generate the necessary transmission energy directly when
they are pressed. There is no need for any batteries and the components require no maintenance.
Safety and installation instructions
•
The relevant safety and accident prevention regulations must be observed.
Using the equipment for any purpose other than its intended use may lead to
damage or destruction.
00
1
_
1
1
09
06
G
B
OSRAM - Operating instructions: TOUCH DIM RMC
page 3
Installation
Design and dimensions
49 mm
button 2
button 4
button 3
button 1
page 4
OSRAM - Operating instructions: TOUCH DIM RMC
Start- up and operation
Learning the handheld transmitters
Touch DIM RMC unit provides four push buttons, operating as two pairs (button 1 + 2 and 3 + 4).
Each pair corresponds with the two channels of a Touch DIM receiver. Thus two Touch DIM RC
modules with two channels may be controlled individually by the RMC.
Before an ECG connected to a Touch DIM RC module can be controlled, the relevant radio
transmitter has to be learned to the receiver.
Hold down the button marked “press to activate learn mode” on the receiver with a suitable tool (such
as an insulated screwdriver) until the “Learn mode active” LED starts to flash. Alternatively, this learn
mode can be activated by an external switch (make contact) connected to the “Learn” terminals.
Now press one of the buttons of a pair on the RMC unit that should be learned. On receipt of a radio
telegram, the LED lights up for 4 seconds, then goes out for a further 4 seconds and then continues
to flash to confirm that it has been successfully learned. While the LED is flashing further wall
transmitters can be learned.
In each case, both channels belonging together (buttons 1 + 2
or
3 + 4) of a RMC are learned so that
ECG connected to Ch1 and Ch2 (i.e. Group 1 and Group 2 of a receiver module) can be operated.
Î
button 1 controls Ch1, thereby button 2 automatically controls Ch2 of the first receiver
Î
button 3 controls Ch1, thereby button 4 automatically controls Ch2 of the second receiver
Therefore there is no need to learn the second transmitter channel of a pair separately.
The learn mode can be terminated by pressing the “press to activate learn mode” button again or with
an external switch connected to the “Learn” terminals. The learn mode is automatically terminated if a
wall transmitter has not been operated for 30 seconds.
Unlearning / cancelling transmitters
Radio transmitters that have already been learned can be easily “unlearned”.
This is also done through the 'learn mode'. Hold down the button marked “press to activate learn
mode” on the receiver with a suitable tool (such as an insulated screwdriver) until the “Learn mode
active” LED starts to flash. Alternatively, this learn mode can be activated by an external switch
(make contact) connected to the “Learn” terminals.
Now operate the RMC to be cancelled. When a radio telegram is received the LED goes out for 4
seconds and then continues to flash to confirm that the cancel process has been successfully
completed. While the LED is flashing further wall transmitters can be cancelled.
In each case, both channels belonging together (buttons 1 + 2
or
3 + 4) of a RMC are unlearned.
There is therefore no need to unlearned the second channel of a pair separately.
The learn mode can be terminated as described above.
Note:
The learning (and unlearning) mode is indicated by the lamps slowly fading u and down in
rhythm with the flashing LED. During the learn mode the sensitivity of the receiver module is
reduced so that neighbouring transmitters are not learned or unlearned by mistake. It may
therefore be necessary to bring the radio transmitter closer to the receiver to ensure
successful learning or unlearning.
