Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
ORing Industrial Networking Corp.
Introduction
PRINTED ON RECYCLED PAPER
Q I G
The
are managed Ethernet switches with
8x10/100/1000Base-T(X) ports, 4x100/1000Base-X SFP ports, and 4
or 8
100Base-X optical fiber
ports with SC connectors.
IGS-9844/9848GPFX series
(IGS-
9844 GPFX series)
(IGS-9848GPFX series)
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
Dimension
Panel Layouts
1
1. SFP fiber ports
2. RJ45 ports
3. Power LED
4. PWR1 LED
5. PWR2 LED
6. R.M. status LED
7. Ring status LED
8. Faulty relay indicator
9. Console port
10. Fiber ports
Package Contents
Contents
DIN-rail Kit
CD
IGS-9848GPFX
IGS-9844GPFX
Pictures
Number
X 1
X 1
X 1
Front View
Top Panel
The
are shipped with the following items. If any
of these items is missing or damaged, please contact your customer service
representative for assistance.
IGS-9844/9848GPFX series
GIGABIT
I N D U S T R I A L
SWITCH
Industrial Managed Gigabit Switch
QIG
Console Cable
X 2
X 1
X 1
Wall-mount Kit
Number
X 1
X 1
X 1
X 2
X 1
X 1
33.0
30.0
12.5
105.5
10.9
15.0
70.5
154.0
96.4
87.0
48.0
17.5
94.0
124.0
48.0
58.0
7.50
R2.5
R3.95
66.25
48.75
95.9
IGS-9848GPFX
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G12
G11
G10
G9
100/1000X
G7
G5
G3
G1
LNK/
ACT
P16
P15
P14
P13
100FX
LNK/
ACT
P20
P19
P18
P17
IGS-9848GPFX
33.0
30.0
12.5
105.5
10.9
15.0
70.5
154.0
96.4
87.0
48.0
17.5
94.0
124.0
48.0
58.0
7.50
R2.5
R3.95
66.25
48.75
95.9
IGS-9844GPFX
IGS-9844GPFX
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G12
G11
G10
G9
100/1000X
G7
G5
G3
G1
LNK/ACT
LNK/ACT
P16
P15
P14
P13
100FX
IGS-9844GPFX
2
IGS-9844GPFX
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G12
G11
G10
G9
100/1000X
G7
G5
G3
G1
LNK/ACT
LNK/ACT
P16
P15
P14
P13
100FX
10
9
3
4
5
6
7
8
IGS-9848GPFX
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G12
G11
G10
G9
100/1000X
G7
G5
G3
G1
LNK/
ACT
P16
P15
P14
P13
100FX
LNK/
ACT
P20
P19
P18
P17
1
2
10
9
3
4
5
6
7
8
IGS-9848GPFX
Rear View
1
2
1. Wall-mount screw holes
2. Din-rail screw holes
PWR-1
PWR-2
1A@24V
DC 48V
V2- V2+
V1- V1+
Fault
1
1. Wall-mount screw holes
2. Din-rail screw holes
2
1. Terminal blocks: PWR1, PWR2
(12-48V DC), Relay
2. Ground wire.
1
Installation
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in
the middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch
clicks into the rail firmly.
DIN-rail Installation
Step 1:
Step 2:
Step 3:
Screw the two pieces of wall-mount kits onto both ends of the rear panel of the
switch. A total of six screws are required, as shown below.
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Insert four screw heads through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the four screws for added stability.
Wall-mounting
IGS-9844GPF
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G12
G11
G10
G9
100/1000X
G7
G5
G3
G1
LNK/ACT
LNK/ACT
G16
G15
G14
G13
1000FX
ORing Industrial Networking Corp.
Copyright© 2013 ORing
All rights reserved.
TEL: +886-2-2218-1066
FAX: +886-2-2218-1014
Website: www.oring-networking.com
E-mail: [email protected]
IGS-9844/9848GPFX Series
IGS-9844/9848GPFX Series
1907-2-29-IGS984XGPFX-1.0
