*
Note
*All pictures in this user's manual are for reference only.
*
Supplied Accessories
Figure 3
Figure 4
Figure 5
Figure 1
Figure 2
Do not use the radio in area where government law prohibited.
Do not use the radio in gas station, airport or places where using radio is prohibited.
Do not expose the radio to long period of direct sunlight, nor place it close to
heating appliances.
Do not place the radio in excessively dusty and/or humid areas, nor on unstable
surface.
Do not expose the radio to rain or moisture; to prevent fire or electric shock.
If you detect an abnormal odor or smoke coming from the radio, turn off the radio
or remove the battery from the radio immediately. Contact Olywiz Customer
Service Center immediately.
Maintenance should only be attempted by professional technicians.
*
Installing the antenna
*
Installing the belt clip
*
Installing external accessories
*
Charging the battery
*
Installing the battery
Note :
Carefully unpack the radio. We recommend that you identify the items listed in the following
table before discarding the packing material. If any items are missing or have been
damaged during shipment, file a claim with the carrier immediately.
Hold the antenna at the base, rotate clockwise into
the threaded connector on the top of the radio.
Note:
Do not over tighten to prevent damage of the
antenna. ( Figure 3 )
Remove the screws on the back of the radio; align
the belt clip with the screw holes on the radio, then
tighten the screws.
To remove the belt clip, loosen the screws and take
out the belt clip, then tighten the screws back to the
radio.( Figure 4 )
1.Connect the AC adapter to the charging port of
desktop charger, then plug the other end of the AC
adapter to a wall outlet or power strip (100-240V~50/
60Hz). The LED will light in ORANGE, then turn to
Red and remain in GREEN indicating the charger
is being supplied with power.
2.Turn off your radio, place the battery alone or with
the radio into the charger. Be sure the battery is well
connected with the charger contacts.
3.When the battery or radio has been put into the
desktop charger, the LED will turn to RED and remain
solidly on. This is an indicator that the battery is
charging. Charging time depends on the battery
capacity. Once the battery is completely charged,
the GREEN LED light will remain on solidly.
* To shorten the charging time, we recommend that you power off the radio while charging.
* Battery capacity will decrease when the ambient temperature is above 35
*
or below-10
*
.
* Do not disassemble the charger and battery. Do not throw the battery into the fire or heat.
* Be sure and protect the contacts (of the charger and the battery) to avoid accidental
shorts of the terminals.
Antenna
To install the battery: Take out the radio, slide the battery down onto the back of the
radio, then push up the battery latch until it locks into place. (Figure 1)
To remove the battery: Turn off the radio; then unlock the battery latch and take out
the battery from the radio. (Figure 2)
Caution
FCC Warning
Pull out the rubber cover (marked with SP/MIC),
insert the accessory plug into the speaker/mic jack.
Note:
Be sure the accessory plug well contacted with the
jack.( Figure 5 )
Two-way Radio
User's Manual
Please read this manual carefully before use and keep for further reference.
Unpack and Check Equipment
Preparation
Technical Specifications
Frequency
Voltage
Channel Number
RF Power
Dimensions
weight
406-470MHz
7.4V (Li-ion)
16
5W
60mmx35mmx126mm(exclude antenna)
193g(with battery and antenna)
Preparation
GTS-813
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
*Note*Other frequency can be customized by PC programming software.
The technical specification above is for reference only.
