background image

 

Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-BI30 Binocular Viewing Head

 

(

Rev. 1)

 

Page 1 of 34

 

Complete Teardown, Cleaning, and 

Reassembly of the Olympus BH2-BI30 

Binocular Viewing Head

  

(Revision 1) 

 

Copyright © 2017 Carl Hunsinger 

All  rights  reserved.    This  document  may  not  be  reproduced  or  distributed,  in  whole  or  in  part,  for  any  commercial 
purpose  without  the  express  written  consent  of  the  author  ([email protected]).   Permission  is  hereby  granted  to 
distribute this PDF document in its entirety for personal, non-commercial purposes only, provided that the contents are 
not modified in any way, including the copyright notices contained herein.  This document may be freely distributed on 
WWW,  FTP,  or  BBS  sites  in  accordance  with  these  restrictions.    The  content  of  this  document  is  provided  for 
informational  purposes  only,  with  no  expressed  or  implied  warranties  whatsoever,  including,  but  not  limited  to, 
function, suitability, safety, accuracy, or completeness of information. 

Revision History 

Revision 

Description of Changes 

Date 

*** Initial Release *** 

9-19-2017 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for BH2-BI30



































Reviews: