background image

Olympic Drives & Equipment Sales Ltd.   

 

 
 
 
Olympic Azimuth Drive HD3 & SD1 
360 Degree Marine Propulsion Drive 
 
 

 

 

 
 

Table of Contents 

 

1.0

 

MOUNTING THE OLYMPIC AZIMUTH DRIVE .................................................................... 2

 

2.0

 

INPUT SHAFT .............................................................................................................................. 3

 

3.0

 

LUBE OIL SYSTEM: ..................................................................................................................... 3

 

4.0

 

STEERING HYDRAULICS FOR ENGINE DRIVEN PUMPS ................................................. 4

 

5.0

 

STEERING HYDRAULICS, POWER UNIT .............................................................................. 5

 

6.0

 

REMOTE STEERING CONTROL, MECHANICAL LINKAGE SYSTEM ............................. 6

 

7.0

 

REMOTE STEERING CONTROL, ELECTRICAL CONTROL SYSTEM .............................. 6

 

8.0

 

PROPELLER.................................................................................................................................. 6

 

 

The Olympic HD3 & SD1 allows for 
positive propeller thrust in a full 360-degree 
arc.  The direction of rotation can be changed 
quickly, and a full rotation can be achieved 
in as fast as 3 seconds, allowing maximum 
maneuverability of the vessel.   
 
Specifically designed for rugged commercial 
use, the Olympic HD3 & SD1is backed by a 
limited warranty. 

Summary of Contents for HD3














Reviews: