![background image](http://html1.mh-extra.com/html/olympia-electronics/gr-938-4p-adr/gr-938-4p-adr_manual_3874222001.webp)
Page
1
from
5
923939013_09_004
+20gr
ΤΟ
ADDRESS MODULE
GENERAL
These luminaires are used in places where
emergency luminaires are needed. Each
luminaire must be permanently connected to
mains power supply.
In normal operation (L1
connected to L) the led strip lights and the battery
is charging.
In case of a mains power supply
failure the luminaire will light the led strip
automatically in emergency mode (powered by its
battery). When the mains power supply is
restored the device turns to normal operation.
Address Operation
The luminaires can be connected to a GR-6500
address panel. For address operations refer to
the installation manual of the panel.
For address module connections see page 3.
For dip-switch addressing selection see page 4, 5
and 6.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
Battery Charging
The battery charging is completely controlled
.
In
this case, the best possible battery maintenance
is
achieved
,
as well as the elongation of its
duration
.
When the battery has completely
charged
,
it charges with a maintenance current.
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails
and battery has lost its
energy
.
During this operation the luminaire enters
the idle state
and battery consumption is
negligible, in order to be protected from deep
discharge.
Manual
Test
This test can be done by pressing the
TEST/RESET button briefly (page 3). The light
source and the emergency circuit of the device is
monitored. The manual test can be conducted only
if the mains power supply and the battery is
connected. During this test period all indication
LEDs are OFF.
Tests
Normally the illumination source and the autonomy
tests are programmed by the control panel and the
test results are sent to the control panel.
If the luminaire is not connected to GR-6500
panel, the following automatic tests executed:
Automatic operational test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the mains
power supply and the battery should be
connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted and
ADDRESSABLE WATERPROOF SELF TESTING MAINTAINED EMERGENCY LUMINAIRES WITH WHITE LEDs
GR-938/4P/ADR GR-939/4P/ADR GR-938/6P/ADR GR-939/6P/ADR
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE
Thank you for your trust in our products
Olympia Electronics - European manufacturer
TECHNICAL CHARACTERISTICS
(for LED MODULE Specifications see page )
5
220-240V AC/50-60Hz
5.9W/8.4VA
5W/7.7VA
6W/8.5VA
4W/7.5VA
Bayblend FR3010
,
transparent
polycarbonate
180min
180min
90min
90min
24h
Charge, lamp fault, fault indication LED
From overcharge and deep discharge
IP65
4.8V/1.5Ah
4.8
V/4Ah(Ni-MH)
4.8
V/
3
Ah
175/350lm
245/480lm
4 white power LEDs
6 white power LEDs
o
5 to 40 C
Up to 95%
3 years
(1
year for the battery
)
940gr.
1030gr.
1080gr.
363 x 145 x 73 mm
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3