background image

Outdoor Living Today                www.outdoorlivingtoday.com             [email protected]

Page 1

Important Information: 

- It is the sole responsibility of the customer to check with your local municipal or county by-laws before  
  ordering this product to confirm it complies with building codes in your area. 
- If the product is elevated, any structural and building code requirements are solely the customer's  
  responsibility, and should be abided by. 

 

- Snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep    
  snow off roof frequently. 
- In areas with high or gusty wind conditions, it is advisable to install the structure securely to the ground. 
- Have a regular maintenance plan to ensure screws, doors, windows and parts are tightly affixed.  
- All structures purchased from Outdoor Living Today are covered for a period of one year for defects in  
  manufacturing and workmanship. Costs incurred for customer installations are not included. 
- Failure to use supplied parts included in this kit could result in poor product performance and may void    
  your warranty. Please contact Outdoor Living Today’s Customer Toll Free Line if you plan to deviate from   
  our  written instructions.

Thank you for purchasing a 
12x8 Cabana.  Please take 
the time to identify all the 
parts prior to assembly. 

Version #1.0 
September 28, 2023

In the event of a missing or broken piece, simply call the Outdoor Living Today Customer Support Line  
@ 1-888-658-1658 within 30 days of the delivery of your purchase. It is our commitment to you to courier  
replacement parts, free of charge, within 10 business days of this notification. Replacement parts will not be 
provided free of charge after the 30 day grace period. 

Stock Code: 
CB128-SLIDER-CEDAR-BEV

Customer agrees to hold Outdoor Living Today and any Authorized Dealers free of any liability for improper  
installation, maintenance and repair.

12x8 CABANA SLIDER 

 

WITH BEV SIDING & CEDAR 

ROOF

 

Summary of Contents for CABANA CB128-SLIDER-CEDAR-BEV











































Reviews: