manualshive.com logo in svg
background image

8807564          12/12

21° 3-1/2 INCH FULL ROUND HEAD

FRAMING NAILER

CALIFORNIA PROPOSITION 65

WARNING: You can create dust
when you cut, sand, drill or grind
materials such as wood, paint,
metal, concrete, cement, or other
masonry. This dust often
contains chemicals known to
cause cancer, birth defects, or
other reproductive harm. Wear
protective gear.

WARNING: This product or its
power cord may contain
chemicals, including lead,
known to the State of California
to cause cancer and birth
defects or other reproductive
harm. Wash hands after
handling.

Important!

When using equipment, a few
safety precautions must be
observed to avoid injuries and
damage. Please read the complete
operating manual with due care.
Keep this manual in a safe place,
so that the information is available
at all times. If you give the
equipment to any other person,
give them these operating
instructions as well. We accept no
liability for damage or

accidents which arise due to
non-observance of these
instructions and the safety
information herein.

SPECIFICATIONS

Normal Operating Pressure:

75 PSI - 120 PSI

Firing Mode:

 Sequential Fire/

Bounce Fire

Fastener Size Range:

2 inches to 3-1/2 inches

Capacity: 

55 pieces

FEATURES

• Comfortable rubber grip
• Lightweight magnesium
housing
• Adjustable depth of
penetration
• Anti-dry firing mechanism
• Single sequential, full
sequential, and bounce action
are exchangeable.

• No-Mar Tip protects work
surface.

Keep this manual and
receipt in a safe and dry
place for future reference.

CAUTION:

FOR YOUR OWN SAFETY
READ INSTRUCTION
MANUAL COMPLETELY
AND CAREFULLY BEFORE
OPERATING THIS 3-1/2
INCH CLIPPED HEAD
FRAMING NAILER.

Any failures made in
following the safety
regulations and
instructions may result in
an electric shock, fire
and/or serious injury.

EXPLANATION OF
NAILING ACTION

• SINGLE ACTUATION
MECHANISM: First, press the
safety against the wood.
Next, pull the trigger to drive
the fastener. After fastening
once, fastening will not be
possible again until the trigger
is released and pressed
again.

Model: 7564

For Customer Service, please call 

1-800-348-5004

 or email 

[email protected]

Содержание 7564















Отзывы: