![background image](http://html.mh-extra.com/html/nokta-makro/gold-finder-2000/gold-finder-2000_quick-manual_1699632001.webp)
Turning On/Off the Device
To turn on the device, press and hold the On/Off button until the
bar starts filling up. To turn off the device, press and hold the button
until the display light turns off.
Sensitivity
This is the depth setting of the device. It is also used to
eliminate the ambient electromagnetic signals from the
surrounding environment and noise signals transmitted
from ground.
Sensitivity setting consists of 8 levels and is pre-defined for each
mode. Each mode starts with its default sensitivity setting and it can
be manually modified when necessary.
Note :
If the ground is highly mineralized causing the device to
overload, decrease the Sensitivity until the overload warning icon
disappears from the screen.
Pinpoint
Pinpoint is to find the center or the exact location of a detected target.
To perform pinpoint :
1- After a target is detected, move the search coil aside where there
is no target response and push the Pinpoint button .
2- Keep the button pressed down and bring the search coil closer to
the target slowly and parallel to the ground.
3- Signal sound becomes stronger and changes in pitch while getting
closer to the target center. In addition, the bar on screen will rise or
fall based on signal strength.
4- Mark the position which provides the loudest sound using a tool or
your foot.
5- Repeat the above procedure by changing your direction 90°.
Actions to be performed from a couple of different directions will
narrow the target area and provide you with the most exact details
of the target location.
Frequency Shift
It is used to eliminate the electromagnetic interference that the device
receives from another detector which operates in the same frequency range
nearby or from the surroundings. If too much noise is received when the
search coil is lifted in the air, this may be caused by the local electromagnetic
signals or excessive sensitivity settings.
To shift the frequency, press and hold the M button for 3 seconds while
the device is on. The frame around the search modes icon will start blinking.
Change the frequency using the sensi/- buttons.
Note :
If no button is pressed for 5 seconds, the screen will time out and the
device will revert back to the main screen.
Frequency shift will be reflected on the left side of the bar. The left side of the
bar will start filling up / falling each time you press the sensi/-
buttons. Frequency shift consists of 10 steps and 5 is the central frequency.
IMPORTANT!
At each power up, the frequency shift setting will start at the
central frequency of 5.
Search Modes
There are 2 search modes: All Metal and Discrimination. Press the M
button to select the mode.
All Metal Mode
In this mode, the device does not provide audio tone discrimination
and gives the same audio tone for all types of targets.
Discrimination Mode
In this mode, the device does NOT provide any audio tone for ferrous
metals and it provides a high tone for non-ferrous metals.
In both search modes:
When the device detects a ferrous metal, the left side of
the bar fills up in proportion to the strength of the target
signal.
When the device detects a non-ferrous metal, the right
side of the bar fills up in proportion to the strength of the
target signal.
1) On / Off Button
2) Search Mode Button
3) Search Modes
4) Pinpoint Button
5) Volume Buttons
6) Sensitivity Buttons
7) Signal Strength Bar
8) Warning Icons
9) Battery Icon
10) Wireless Connection Icon
Control Display
Illumination LEDs
It is the flashlight used for lighting the area you are scanning while detecting
at night or in dark locations. To activate the LEDs, while the detector is on,
press the pinpoint and volume minus (-) buttons at the same time. Repeat
the same to turn them off. LEDs do not operate when the device is off. It is
recommended to turn them on only when necessary since they consume
extra battery power.
Volume
Press the + or - button to adjust the volume.
QUICK GUIDE
2
1
7
8
9
10
4 5
6
3