background image

© 2020 NavePoint, LLC 

20200910-01 

 

 
 
 
 

 

OWNER’S MANUAL: Hinged Wall

-Mount Rack (9U/12U/15U) 

 

 

Keep this information for further reference. 

Thank you for purchasing a NavePoint product. 

Please examine the product for any damaged parts. If any part is damaged or missing, contact NavePoint for assistance. Do not 
attempt to install or use product if it has been damaged. This product contains small items that could be a choking hazard 

– keep these 

items away from children. 

 

During installation, lay product contents on cardboard or other protective surface to avoid any damage. 

Do not use with equipment that is heavier than the indicated weight capacity for this product. This product is designed to be installed 
indoors on wood stud walls, solid concrete walls or brick walls. Make sure that the supporting surface will safely support the weight of 
the equipment and all attached hardware and components. It is recommended that installation be performed by a qualified installer. 
NavePoint cannot be held responsible for damage to equipment or personal injury resulting from improper use or installation of 
product. 

 

Maintenance: Check that the product is secure and safe to use at regular intervals (at least every three months). 

Limitations of Liability: In no event will NavePoint, LLC. be liable for any damages, whether direct or indirect, special, punitive, 
incidental or consequential damages (including, but not limited to, lost profits or revenue, loss of use, lost business opportunities or loss 
of goodwill) or for the costs of procuring substitute products, arising out of or in connection with the use of the product, whether such 
liability arises from any claim based upon contract, warranty, tort (including negligence), product liability or otherwise, whether or not 
seller has been advised of the possibility of such loss or damage. In no event will seller’s total cumulative liability, from all causes of 
action and all theories of liability, exceed the total amounts actually paid to seller by customer under the order that gives rise to any 
liability hereunder. 

THIS MANUAL APPLIES TO THE FOLLOWING SKUs: 00301324, 00301325, 00301326 

Summary of Contents for 00301324







Reviews: