National Instruments SCXI SCXI-1102 Calibration Procedure Download

Page: 1 / 18

CALIBRATION PROCEDURE

SCXI -1102/B/C

For NI-DAQmx

This document contains information and instructions for calibrating the
National Instruments SCXI-1102/B/C signal conditioning module.

Contents

Initial Setup...................................................................................... 5
Verification Procedure ..................................................................... 7
Adjustment Procedure...................................................................... 12
Verifying Adjusted Values .............................................................. 14

Test Limits .............................................................................................. 14

Gain and Offset ................................................................................ 15

SCXI-1102/B/C Front and Rear Panel Diagrams ................................... 15
World Wide Support and Services.......................................................... 18

™

Summary of Contents for SCXI SCXI-1102



















Search results

Summary of Contents for SCXI SCXI-1102

Reviews:

Related manuals for SCXI SCXI-1102

Brands by name

Popular brands

National Instruments SCXI SCXI-1102, Calibration Procedure

Search results

Summary of Contents for SCXI SCXI-1102

Reviews:

Related manuals for SCXI SCXI-1102

Brands by name

Popular brands