background image

 

 
 
 
 

Bed Watcher 

 

User’s Guide 

 

Revision 1.2 

30-Jun-2016 

 

 

 

 

 

 

 

 

 

 

 

 

 

© Copyright 2007-2016 NanoPulse, Inc. All rights reserved. 

 

NanoPulse,  Inc.  reserves  the  right  to  make  changes  without  further  notice  to  any  products  herein  to  improve  reliability, 
function or design. NanoPulse, Inc. does not assume any liability arising out of the application or use of any product described 
herein; neither does it convey any license under its patent rights nor the rights of others. NanoPulse products are not designed, 
intended,  or  authorized  for  use  as  components  in  systems  intended  for  surgical  implant  into  the  body,  or  other  applications 
intended to support or sustain life, or  for any other application in  which the  failure of the NanoPulse product could create  a 
situation where personal injury or death may occur. Should Buyer purchase or use NanoPulse products for any such unintended 
or  unauthorized  application,  Buyer  shall  indemnify  and  hold  NanoPulse,  Inc.  and  its  officers,  employees,  subsidiaries, 
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out 
of, directly or indirectly, any  claim of personal injury or death associated  with such unintended or unauthorized use,  even  if 
such claim alleges that NanoPulse, Inc. was negligent regarding the design or manufacture of the part. 

Summary of Contents for Bed Watcher












Reviews: