The cooktop, as shipped from the
factory, is set for use with its intended
gas. If you wish to use your cooktop with the alternate
gas, you must first replace the orifices and convert
the pressure regulator. Failure to do so may result in
carbon monoxide poisoning or fire.
Rear Leg
Extension Rod
Rear Vent Trim
Control Panel
Bezels
Surface Knobs
MODEL
NUMBERS
ZGP366N,
ZGP364NR,
ZGP364ND,
CGY366SELSS,
ZGP366L,
ZGP364LR,
ZGP364LDS
IMPORTANT
SERVICE
INFORMATION
DO
N
OT
D
ISCARD
31-17280
10-2017
GEA
Printed
in
Mexico
TAPE
AREA
Set Screw
Loosen
WARNING
Explosion Hazard
Death or serious injury can result from failure to follow
these instructions.
• Service by a qualified service technician only.
• Shut off gas supply and disconnect power before
servicing.
• Reconnect all grounding devices after service.
• Replace all parts and panels before operating.
36” ALL GAS RANGES
36” Natural Gas Surface Burner Models: ZGP366N,
ZGP364NR, ZGP364ND, CGY366SELSS
36” Propane (LP) Gas Surface Burner Models:
ZGP366L, ZGP364LR, ZGP364LDS
ANTI-TIP DEVICE
The Anti-Tip Bracket must be properly installed to prevent tipping
of the range. Failure to do so can cause serious damage or injury.
After servicing, roll the range into position, being careful not to
entangle or pinch the power cord and flexible gas tubing. Make
sure the Anti-Tip Bracket is engaged.
REMOVE/REPLACE RANGE
To roll the range from its location for service, lower the range onto its
wheels by retracting its four leveling legs.
SURFACE KNOB INDICATOR LIGHT REPLACEMENT
Remove the control panel. See the
CONTROL PANEL REMOVAL
section. Find the indicator light on top of the gas valve, remove the
attached screw and replace.
WARNING
GAS CONVERSION KIT
The gas conversion kit is located behind the front access panel at
the bottom of the range. Please refer to the
Installation Instructions
for details on removal.
GAS SUPPLY REQUIREMENTS
GAS TYPE
INCOMING PRESSURE
TO REGULATOR
PRESSURE REGULATOR
OUTPUT
Natural
WR:&3
:&3
Propane (LP)
WR:&3
:&3
Be sure Anti-Tip Bracket
is engaged with the
brace on the range.
FRONT LEVELING LEGS ADJUSTMENT
A leveling leg wrench is supplied. Reach under the front of the range
near the right side. Locate and remove a thumb screw, then slide the
wrench out of the slot.
Slide the front cylinders up to adjust the front leveling legs. Be careful
not to damage the cylinder.
Use the supplied wrench to turn the
front leveling legs. Turn clockwise to
raise the range above the wheels.
Turn counterclockwise to lower the
legs.
Be sure to return the wrench to its
storage slot for future use.
Slide leg
cylinder
up.
Thumb Screw
REAR LEVELING LEGS ADJUSTMENT
Remove the two screws from the rear vent trim. Slide the vent trim
forward, then lift up to remove.
Find the two rear leg extension rods. Use a 1/4” driver or wrench on
the extension rods to adjust the rear legs.
CONTROL PANEL REMOVAL
Pull the surface knobs off and remove the screws from each bezel.
Remove the screws from the control panel face.
NOTE:
Do not
remove the oven control knob.
Remove the screws from the bottom of the control panel and from the
top (inside flanges, on each side, on the back side of the panel).
ACCENT LIGHTING REPLACEMENT
Remove the control panel. See the
CONTROL PANEL REMOVAL
section.
Loosen the accent lighting module’s screw, slide out and replace.
OVEN CONTROL ACCESS
Remove the control panel. See the
CONTROL PANEL REMOVAL
section.
The oven control is mounted to the back side of the control panel.
SPARK MODULE REPLACEMENT
1.
Roll the range from its installation position.
See the
REMOVE/REPLACE RANGE
section.
2.
Remove the control panel. See the
CONTROL PANEL
REMOVAL
section.
3.
Remove the two screws from the rear vent trim and remove the
trim.
4.
Remove the side range panel by removing the screws on the
back of the range and the screws from the range face top inner
corners, and then lift the panel up and off of its front keyhole
mounting slots.
5.
Remove the left grates and left grate frame. Remove surface
burners by removing all screws, but keep the outside burner
screws separate from the inside burner screws so they can
be easily replaced. Remove the burner pan, burner insulation
and spark module cover. Disconnect the igniter wires by pulling
them off of the connector pins.
HIGH ALTITUDE KIT
)RURSHUDWLRQIURPWRIHHWRUGHU:%.
Conversion Kit. This kit includes orifices for both propane (LP) and
natural gas operation.
Grates
Grate Frame
Surface
Burners
Spark Module Cover
Burner Pan
Burner
Insulation
GRILL IGNITER REPLACEMENT
Remove the grill cover, grate,
grate frame and radiant baffle.
Remove the screws from each
side of the pan surround and
remove the pan surround.
Remove the screws from the
igniter and pull the igniter
connector from the opening.
Disconnect the connector pin
and replace the igniter. Push
the igniter connector back into
the opening and replace all
parts.
Grill
Grate
Grill
Grate
Frame
Radiant
Baffle
Pan
Surround
GRIDDLE IGNITER REPLACEMENT
Lift off the griddle flue cover. Remove the 2 inside clamping screws.
NOTE:
Remove the 2 screws positioned on the inside only. Do not
remove the outermost screws—they are for leveling the griddle.
Slide the griddle toward the rear and out of the hold-down tabs
along the bottom front.
CAREFULLY
lift and hold the griddle. A thermostat capillary is
routed through a clip. Gently lift the griddle to one side and slip the
capillary out of the clip. Do not disconnect or pull on the capillary.
Gently lay the griddle aside.
Remove the 2 burner hold-down screws at the rear of the burner
to loosen the burner. Remove the screws attaching the igniter.
Pull the igniter connector from the opening, disconnect the pin
connection and replace the igniter. Route the capillary back into
the clip. Push the excess capillary back through the opening. Push
the igniter connector back into the opening and replace all parts.
GAS MANIFOLD AND VALVE REPLACEMENT
Refer to the
Service Manual
for replacement procedure.
Griddle Flue Cover
Capillary
Igniter
Leveling
Screws
Clamping
Screws
Slide back
griddle and
lift front
Avoid routing capillary
through burner flame area.
*($
