-
FX
3UC
(D,DSS) SERIES
PROGRAMMABLE CONTROLLERS
HARDWARE MANUAL
This manual describes the part names, dimensions, mounting,
cabling and specifications for the product. This manual is extracted
from FX
3UC
Series User's Manual - Hardware Edition. Refer to
FX
3UC
Series User's Manual - Hardware Edition details. Before use,
read this manual and manuals of relevant products fully to acquire
proficiency in the handling and operating the product. Make sure to
learn all the product information, safety information, and precautions.
And, store this manual in a safe place so that it can be taken out and
read whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this
manual are the registered trademarks or trademarks of each
company.
Effective November 2007
Specifications are subject to change without notice.
©
2007 Mitsubishi Electric Corporation
Safety Precaution
(Read these precautions before use.)
This manual classifies the safety precautions into two categories:
and
.
Depending on the circumstances, procedures indicated by
may also cause severe injury.
It is important to follow all precautions for personal safety.
Certification of UL, cUL standards
The FX
3UC
main units and input/output extension units/blocks
supporting UL, cUL standards are as follows:
UL, cUL file number :E95239
Models :
MELSEC FX
3U(C)
series manufactured
FX
3UC
-
MT/D
FX
3UC
-
MT/DSS
Where
indicates:16,32,64,96
FX
3U
-232ADP(-MB)
FX
3U
-485ADP(-MB)
FX
3U
-4AD-ADP
FX
3U
-4DA-ADP
FX
3U
-4AD-PT-ADP
FX
3U
-4AD-TC-ADP
FX
3UC
-1PS-5V
Models :
MELSEC FX
2NC
series manufactured
FX
2NC
-16EX(-DS)
FX
2NC
-32EX(-DS)
FX
2NC
-16EYT(-DSS) FX
2NC
-32EYT(-DSS)
FX
2NC
-16EX-T(-DS)
FX
2NC
-16EYR-T(-DS)
Manual Number
JY997D28601
Revision
B
Date
November 2007
Indicates that incorrect handling may cause
hazardous conditions, resulting in death or
severe injury.
Indicates that incorrect handling may cause
hazardous conditions, resulting in medium or
slight personal injury or physical damage.
STARTUP AND
MAINTENANCE
PRECAUTIONS
•
Do not touch any terminal while the PLC's power is on.
Doing so may cause electric shock or malfunctions.
•
Before cleaning or retightening terminals, cut off all phases of
the power supply externally.
Failure to do so may cause electric shock.
•
Make sure to connect the battery for memory backup correctly.
Do not charge, disassemble, heat, short-circuit, or expose the
battery to fire.
Doing so may rupture or ignite it.
•
Before modifying or disrupting the program in operation or
running the PLC, carefully read through this manual and the
associated manuals and ensure the safety of the operation.
An operation error may damage the machinery or cause accidents.
STARTUP AND
MAINTENANCE
PRECAUTIONS
•
Turn off the power to the PLC before attaching or detaching the
memory cassette. If the memory cassette is attached or
detached while the PLC's power is on, the data in the memory
may be destroyed, or the memory cassette may be damaged.
•
Do not disassemble or modify the PLC.
Doing so may cause fire, equipment failures, or malfunctions.
For repair, contact your local Mitsubishi Electric distributor.
•
Turn off the power to the PLC before connecting or disconnecting
any extension cable.
Failure to do so may cause equipment failures or malfunctions.
•
Turn off the power to the PLC before attaching or detaching the
following devices.
Failure to do so may cause equipment failures or malfunctions.
- Peripheral devices, extension blocks, connector conversion
adapter, extension power supply units, special adapters, and
FX Series terminal blocks.
- Battery and memory cassettes
DISPOSAL
PRECAUTIONS
•
Please contact a certified electronic waste disposal company
for the environmentally safe recycling and disposal of your
device.
TRANSPORT AND
STORAGE
PRECAUTIONS
•
Before transporting the PLC, turn on the power to the PLC to
check that the BAT LED is off.
If the PLC is transported with the BAT LED on or the battery
exhausted, the battery-backed data may be unstable during
transportation.
•
The PLC is a precision instrument. During transportation, avoid
impacts larger than those specified in Section 2.1. Failure to do
so may cause failures in the PLC.
After transportation, verify the operations of the PLC.
STARTUP AND
MAINTENANCE
PRECAUTIONS
Models :
MELSEC FX
2N
series manufactured
FX
2N
-8ER-ES/UL
FX
2N
-8EX-ES/UL
FX
2N
-8EYR-ES/UL
FX
2N
-8EYT-ESS/UL
FX
2N
-8EX-UA1/UL
FX
2N
-16EX-ES/UL
FX
2N
-16EYR-ES/UL
FX
2N
-16EYT-ESS/UL FX
2N
-16EYS
Compliance with EC directive (CE Marking)
This document does not guarantee that a mechanical system
including this product will comply with the following standards.
Compliance to EMC directive and LVD directive of the entire
mechanical system should be checked by the user / manufacturer.
For more details please contact the local Mitsubishi Electric sales
site.
Requirement for Compliance with EMC directive
The following products have shown compliance through direct
testing (of the identified standards below) and design analysis
(through the creation of a technical construction file) to the European
Directive for Electromagnetic Compatibility (89/336/EEC) when used
as directed by the appropriate documentation.
Type :
Programmable Controller (Open Type Equipment)
Models :
MELSEC FX
3U(C)
series and FX
2NC
series
manufactured
from May 1st, 2005
FX
3U
-FLROM-16
FX
3U
-FLROM-64L
from June 1st, 2005
FX
3U
-232ADP
FX
3U
-485ADP
FX
3U
-4AD-ADP
FX
3U
-4DA-ADP
FX
3U
-4AD-PT-ADP FX
3U
-4AD-TC-ADP
FX
3U
-FLROM-64
from April 1st, 2007
FX
3U
-232ADP-MB
FX
3U
-485ADP-MB
from September 1st, 2007 FX
3UC
-
MT/D
FX
3UC
-
MT/DSS
Where
indicates:16,32,64,96
from October 1st, 2007
FX
3UC
-1PS-5V
FX
2NC
-
EX
FX
2NC
-
EYT
FX
2NC
-
EX-DS
FX
2NC
-
EYT-DSS
Where
indicates:16,32
FX
2NC
-16EX-T
FX
2NC
-16EX-T-DS
Models : MELSEC FX
2NC
series manufactured
from March 1st, 1999
FX
2NC
-
EX-DS
FX
2NC
-
EYT-DSS
Where
indicates:16,32
from August 1st, 1999 FX
2NC
-16EX-T-DS FX
2NC
-16EYR-T-DS
from October 1st, 2007 FX
2NC
-
EX
FX
2NC
-
EYT
Where
indicates:16,32
FX
2NC
-16EX-T
FX
2NC
-16EYR-T
Models : MELSEC FX
2N
series manufactured
from July 1st, 1997
FX
2N
-16EX-ES/UL FX
2N
-16EYR-ES/UL
FX
2N
-16EYT-ESS/UL
from August 1st, 2005 FX
2N
-8ER-ES/UL
FX
2N
-8EX-ES/UL
FX
2N
-8EYR-ES/UL FX
2N
-8EYT-ESS/UL
For the products above, PLC’s manufactured
before March 31st, 2002 are compliant with EN50081-2 (EN61000-
6-4) and EN50082-2 only.
PLC’s manufactured from April 1st, 2002 to April 30th, 2006 are
compliant with EN50081-2 (EN61000-6-4) and EN61131-
2:1994+A11:1996+A12:2000
PLC’s manufactured after May 1st, 2006 are compliant with
EN61131-2:2003
Standard
Remark
EN61131-2:2003
Programmable
controllers
- Equipment
requirements and
tests
Compliance with all relevant aspects of
the standard.
EMI
•
Radiated Emissions
•
Mains Terminal Voltage Emissions
EMS
•
RF immunity
•
Fast Transients
•
ESD
•
Surge
•
Voltage drops and interruptions
•
Conducted
•
Power magnetic fields
Standard
Remark
EN61000-6-4:2001
- Generic emission
standard Industrial
environment
EN50081-2:1993
Electromagnetic
compatibility
Compliance with all relevant aspects of
the standard.
•
Radiated Emissions
•
Mains Terminal Voltage Emissions
EN61000-6-2:2001
- Generic immunity
standard Industrial
environment
Compliance with all relevant aspects of
the standard.
•
RF immunity
•
Fast Transients
•
ESD
•
Conducted
•
Surge
•
Power magnetic fields
•
Voltage drops and interruptions
Standard
Remark
EN61000-6-4:2001
- Generic emission
standard Industrial
environment
EN50081-2:1993
Electromagnetic
compatibility
Compliance with all relevant aspects of
the standard.
•
Radiated Emissions
•
Mains Terminal Voltage Emissions
EN50082-2:1995
Electromagnetic
compatibility
- Generic immunity
standard Industrial
environment
Compliance with all relevant aspects of
the standard.
•
RF immunity
•
Fast Transients
•
ESD
•
Conducted
•
Power magnetic fields
EN61131-2:1994
/A11:1996
/A12:2000
Programmable
controllers
- Equipment
requirements and
tests
Compliance with all relevant aspects of
the standard.
•
RF Immunity
•
Fast Transients
•
ESD
•
Damped oscillatory wave
JY997D28601B(ENGLISH)
