Safety Information
Important Safety Information
♦
Installation and removal of the PoE Midspan must be
carried out by qualified personnel only.
♦
The external power supply for the equipment shall be a
Listed, Direct Plug In power unit, marked Class 2, or
Listed ITE Power Supply, marked LPS, which has
suitably rated output voltage, and current.
♦
AC Power inlet Set:
The power connector supplied with the PoE
Midspan has 2 terminals (See Figure 2) –
The polarity of the input connection is not
important.
The power inlet cables must be rated for
minimum current capacity of 6 Amperes (Stranded
Tinned Copper 12 AWG for each terminal or
2X16 AWG for each terminal).
Before connecting power inlet cables to the
connector terminals verify that the power source
is turned off.
After insertion of cable inlet to the connector
terminals tightly fasten all 4 connector screws
(See Figure 2).
This clause is optional:
Only for improved EMI performance, connect chassis
ground connection to "Earth/Ground" connection at
the working area.
:
There is no safety hazard when the chassis ground
connection is not connected to the "Earth/Ground".
:
The PoE injector "DATA IN" and "DATA & POWER OUT"
ports are shielded RJ45 data sockets. They cannot be
used as Plain Old Telephone Service (POTS) sockets. Only
RJ45 data connectors may be connected to these sockets.
The
24
VAC power source must be near the PoE Midspan and
easily accessible. You can remove AC power from the PoE
Midspan by disconnecting the
24
VAC power inlet from either the
24
VAC power source or the PoE Midspan power connector.
The PoE Midspan "DATA IN" and "DATA & POWER OUT"
interfaces are qualified as SELV (Safety Extra-Low Voltage)
circuits according to IEC 60950-1. These interfaces can only be
connected to SELV interfaces on other equipment.
WARNINGS!
•
Read the installation instructions before connecting the PoE
Midspan to its power source.
•
Follow basic electricity safety measures whenever connecting
the PoE Midspan to its power source.
•
A voltage mismatch can cause equipment damage and may
pose a fire hazard. If the voltage indicated on the label is
different from the power outlet voltage, do not connect the PoE
Midspan to this power outlet.
•
Take extra attention when connecting the power inlet
terminals, so they will not touch chassis ground.
Mounting Instructions
Perform the following instructions:
1.
Install two screws in the wall or shelf as shown in Figure 1.
Figure 1: PoE Midspan mounting instructions
2.
Align the PD-9501G/24AC mounting slots to capture the surface
screws
Recycling and Disposal
Disposal instructions for old products. The WEEE (Waste
Electrical and Electronic Equipment) national environmental
initiatives has been put in place to ensure that products are
recycled using best available treatment, recovery and
recycling techniques to ensure human health and high
environmental protection. Your product is designed and
manufactured with high quality materials and components,
which can be recycled and reused. Do not dispose of your
old product in your general household waste bin. Inform
yourself about the local separate collection system for
electrical and electronic products marked by this symbol:
Use one of the following disposal options :
1. Dispose of the complete product (including its cables,
plugs and accessories) in the designated WEEE collection
facilities.
2. If you purchase a replacement product, hand your
complete old product back to the retailer. He should accept
it as required by the national WEEE legislation.
Microsemi Corp.
Ordering information:
•
Product Name:
Microsemi 9501G/24AC
•
Part Number:
PD-9501G/24AC
•
Description:
1-Port 802.3at 4-Pairs Gigabit PoE Midspan
Document P/N PD9501G24AC_UG-EN Rev. B00
0B
Microsemi 9501G/24AC
1B
User Guide
2B
1-Port 802.3at 4-Pairs Gigabit PoE
Midspan, 24VAC input.
Notice
It is Microsemi’s policy to improve its products as
new technology, components, software, and firmware
become available. Microsemi, therefore, reserves the
right to change specifications without prior notice.
Technical Support
If you encounter problems when installing or using this
product, please consult the Microsemi website at:
http://www.microsemi.com
For technical support, call: +972-9-775-5123
In the USA: 1-877-480-2323
Email: [email protected]
