MTX 3292/MTX 3293,
ASYC IV
Portable Digital Multimeter -
100,000 cts
X04002A02 - Ed. 1 - 07/14
The full user’s manual is available on the CD supplied with the
instrument. Download is possible from our support site:
www.chauvin-arnoux.com.
This multimeter complies with the EN 61010-1 safety standard on double
insulation for electronic measuring instruments.
IP 67 as per standard IEC 60529.
Symbols used on the instrument:
Warning: Risk of danger.
Refer to the user’s manual to find out about the
potential dangers and any action to be taken in order to
avoid
them.
Earth
Double insulated
If you use this instrument in a way which is not specified, the protection
provided may be compromised, thus endangering you.
The safety of any system including this instrument is the responsibility of the
assembler of the system.
This instrument has been designed for use indoors:
- in an environment with pollution level 2,
- at an altitude of less than 2000 m,
- at a temperature between 0°C and 50°C,
- with relative humidity < 80 % up to 35°C.
It can be used for measurements on the circuits of:
-
Category III installations
for voltages up to 1,000 V (AC or DC)
relative to earth.
-
Category IV installations
for voltages up to 600 V (AC or DC)
relative to earth.
-
CAT III
: Measurement category III corresponds to measurements
carried out on installations in buildings.
Example: measurements on switchboards, wiring, etc.
-
CAT IV
: Measurement category IV corresponds to the measurements
carried out on the source of low-voltage installations.
Example: meters and measurements on the safety devices protecting
against overcurrents, etc.
For safety reasons, only use suitable cords supplied with the instrument:
they comply with the EN 61010-031 standard. Before each use, make
sure that they are in perfect condition.
When the instrument is connected to the measuring circuits, never touch a
terminal which is not in use. Use only suitable accessories delivered with
the instrument or approved by the manufacturer.
If the measurement category of the accessory is different from that
of the instrument, the lowest category applies to the unit.
6, avenue du Pré de Challes
F-74940
ANNECY-LE-VIEUX
Tél. +33 (0)4.50.64.22.22
MTX 3292
MTX 3293
Display
Graphic color (70 x 52)
Power supply
4 R6 batteries (AA format)
or rechargeable batteries
Counts
100 000
Communication
IR / USB (Bluetooth, optional)
We thank you for your confidence in the quality of our products.
•
Fuse and batteries or rechargeable batteries:
Fuse: 11 A: 10 x 38 - 1000 V
F - breaking capacity:
>
18 kA
4 batteries: 1,5 V AA LR6 or batteries 1,2 V Ni-IMH LSD
•
Terminal block: with 3 4-m banana inputs and an optical
connector for USB communication:
•
Display of the connection on the screen:
Voltage: V
AC
, V
DC
, V
AC+DC
Graphic display of
Mem…
in VAC+DC mode
:
Frequency: Hz
Resistance:
Ω
, Diode, Continuity
Capacitance: F
V
input
2.
Graphic mode (default),
but
select:
y
Meas…
for another display
y
MEAS+
to select a
secondary function
y
REL
relative measurement
y
SURV
for MIN/MAX/AVG
(time-stamped)
y
SPEC
to get the specs
Trace
Zoom
Cursor
1.
Activate "
V",
then
press
F1
,
F2
,
F3
,
F4
to select the coupling:
y
AC,
y
DC,
y
AC+DC
or
y
V
lowZ.
Configuration
SETUP
Æ
MEASURE
to adjust the
parameters: filters,
impedance, reference..
.
COM
input
3.
Select
Mem...
to
save or
stop a sequence (10 max. and
6,500 measurements)
Consult data by long press on
Mem
…
1.
Activate
Ω
by pressing this key:
y
F2
accesses (continuity),
y
F3
accesses 100 Ohm range
y
F4
selects the diodes
(4V or 26V diode test)
y
or subsequent presses
2.
Select
Meas...,
then
MEAS+
for the
MATH
secondary
function,
or:
y
REL relative measurement
y
SURV for time-stamped MIN/MAX/AVG
y
SPEC to obtain the specifications.
1
. Activate
Hz
.
2.
Select
Range
±
,
frequency range
and
< 200 kHz or
> 200 kHz
by the keys
.
3
. Select
Meas…
, then
MEAS+
to select a secondary
function among:
MATH, DCY, PER, PW+/-, CNT+/-
or:
y
REL relative measurement
y
SURV for time-stamped MIN/MAX/AVG
y
SPEC to obtain the specifications.
1.
Activate
C
by pressing this key.
Pressing:
y
F1
accesses
Range+
y
F2
accesses
Range-
Select ranges by those keys
.
2.
Select
Meas...
, then:
y
REL relative measurement
y
SURV for time-stamped MIN/MAX/AVG
y
SPEC to obtain the specifications.
COM
input
V
input
COM
input
V
input
COM
input
V
input
RUN
is displayed
when the
measurement is
running and
OL
is displayed if
the value is >
range or if there
is a short-circuit.
