Metal Fab IPIC Installation And Maintenance Instructions Manual Download

Page: 1 / 24

INSTALLATION AND

MAINTENANCE

INSTRUCTIONS

PIC

IPIC

MODEL PIC/IPIC

CHIMNEY AND VENTS

This symbol on the nameplate

means this product is listed by

Underwriters Laboratories Inc.

and by Underwriters

Laboratories of Canada

A MAJOR CAUSE OF CHIMNEY RELATED FIRES IS

FAILURE TO MAINTAIN REQUIRED CLEARANCES

(air spaces) TO COMBUSTIBLE MATERIALS. IT IS OF

UTMOST IMPORTANCE THAT CHIMNEY BE INSTALLED

ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.

IMPORTANT: DO NOT INSTALL CHIMNEY WITHOUT

FIRST

READING

THESE

INSTRUCTIONS

VERY

CAREFULLY.

Metal-Fab’s Model PIC/IPIC Chimney has been fully tested and listed by Underwriters Laboratories, Inc.

and Underwriters Laboratories of Canada.
Chimneys installed in accordance with these installation instructions will comply with national safety

standards and building codes.
This booklet contains complete information on details concerning dimensions, installation, clearances to

combustibles, and use of non-combustible enclosures. For any additional construction information, refer

to Model PIC/IPIC Design Manual - L1690.

•

BREECHING APPLICATIONS

•

BOILER EXHAUST APPLICATIONS

•

ENGINE/TURBINE EXHAUST APPLICATIONS

METAL-FAB, INC. • P.O. BOX 1138, WICHITA, KANSAS 67201 • (316)943-2351

Summary of Contents for IPIC

























Search results

Summary of Contents for IPIC

Reviews:

Related manuals for IPIC

Brands by name

Popular brands

Metal Fab IPIC, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for IPIC

Reviews:

Related manuals for IPIC

Brands by name

Popular brands