background image

Model

Modèle

Modelo 

C 18DBAL

Cordless Circular Saw

Scie circulaire sans 

fi

 l

Sierra circular a batería

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

 WARNING

IMPROPER OR UNSAFE

 use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and 

understand this manual BEFORE operating the power tool. Please keep this manual 

available for other users and owners before they use the power tool. This manual should be 

stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

 AVERTISSEMENT

Une utilisation 

INCORRECTE OU DANGEREUSE

 de cet outil motorisé peut entraîner la 

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. 

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce 

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent 

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

 ADVERTENCIA

¡La utilización 

INAPROPIADA O PELIGROSA

 de esta herramienta eléctrica puede resultar 

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y 

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual 

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este 

manual debe ser guardado en un lugar seguro.

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

00Book̲C18DBAL̲NA̲metabo.indb   1

00Book̲C18DBAL̲NA̲metabo.indb   1

2021/03/30   17:20:55

2021/03/30   17:20:55

Summary of Contents for C18DBAL










































































































































Reviews: