background image

1501X OPERATIONAL INSTRUCTIONS

 

Thank you for your purchase of the Martin Yale Industries, Inc. 1501X Autofolder. 

Upon receiving the machine, perform an inspection of all components received. 

If you suspect that the unit may have been damaged in transit, call the 

appropriate freight carrier immediately.  If you have any additional questions, 

please contact Martin Yale Industries, Inc. Customer Service department at 260­

563-0641.  

Upon receiving the machine, verify that you have the following components: 

1. 

First Fold Table 

W-A001602 

2. 

Second Fold Table 

W-A001604 

3. 

L Shaped Catch Tray 

W-O001611 

4. 

24 VDC Adapter 

M-S045198 

5. 

Extension Table 

W-O001606 

6. 

Feed Table Wedge 

M-O001661 

1501X SPECIFICATIONS 

PAPER WEIGHT:  16# - 24# BOND STOCK

 

MIN./ MAX WIDTH: 3 ½” – 8 ¾”

 

MIN./ MAX LENGTH: 5” – 14”

 

MAX FEED LOAD: 250 SHEETS (20# BOND STOCK).

 

SPEED: 5,000 – 8,000 PER HOUR.

 

POWER CONSUMPTION: 24 VDC (1A)

 

UNIT IS PROTECTED BY A PTC STYLE CIRCUIT BREAKER.  SHOULD IT LOSE POWER 

FOR ANY REASON, TURN UNIT OFF FOR 60 SECONDS.  IF POWER DOES NOT RETURN, 

CALL TECHNICAL SUPPORT AT Martin Yale Industries, Inc. AT 219-563-0641.

 

http://www.monomachines.com/

http://www.monomachines.com/

Summary of Contents for 1501X








Reviews: