Hoopla Swing
ASSEMBLY INSTRUCTIONS
BEFORE YOU START:
Observing the following statements and
warnings reduces the likelihood of serious or fatal injury.
ASSEMBLY WARNING:
•
Due to the presence of small parts during assembly, keep
out of reach of children until assembly is complete.
To prevent serious injury, children must not use the swing
until properly installed. Do not use swing if any damage or
deterioration is detected or parts are missing. Contact point
of purchase retailer or M&M Sales Enterprises, Inc.
•
Never substitute parts.
•
Please keep instructions for future reference.
ASSEMBLY INSTRUCTIONS:
•
Assembly should be completed by adult person(s). We
intend for our products to bring joy not frustration.
•
A flat level surface approximately 5 ft. x 5 ft. will be
needed to spread out materials for assembly.
•
Two hex wrenches are included for tightening the seven screws.
MM00174 INSTRUCTION MANUAL
ASSEMBLY • INSTALLATION • OPERATION • MAINTENANCE • SAFETY
What’s in the Box
Lay out all box components
included on a level and
comfortable workspace:
PARTS & HARDWARE
(1) A top bar
(1) B bottom bar
(1) C bottom bar
(1) D top bar
(2) E handles
(1) F seat
(1) G rubber cover
(12) H streamers
(1) I carabiner spring clip
8 mm
(1) J clevis holding pin
15mm x 70mm
(1) K washer
15mm x 51mm x 3mm
(2)
L long connecting screw
8mm w/ M6 Thread
(5)
M short connecting screw
8mm w/ M6 Thread
(2) N allen hex wrench
5mm
(1) O swivel spinner
M10 x 304mm
(1) P tree strap
10 ft
A
B
C
D
F
E
G
H
I
K*
L*
M*
*Connecting Screws & Washer
Actual Size Below
J
N
O
P
Figure: 1
At least 6 ft
from the trunk
or 1.5x the
length the
swing
rope.
18”(min)-24”(max) ground clearance.
Tree
Strap
LBS.
150
ASSEMBLY STEPS:
1. Align
A (top bar)
and
D (top bar).
2.
Next, slide
G (rubber cover)
over
D (top bar)
until holes align.
3. Once aligned, insert
A (top bar)
into
G (rubber
cover)
already covering
D (top bar)
.
4. Slide
K (washer)
over
J (holding pin)
and insert through
G (rubber cover)
.
5. Clip
I (carabiner)
onto
J (holding pin)
.
6. Slide
E (handle)
over
A (top bar)
until holes align.
7. Insert
B (bottom bar)
into
A (top bar)
until holes align.
8. Using two
M (short screws)
insert and hand tighten. Using
both
N (hex wrenches)
tighten both screws all the way.
9. Slide
F (seat)
over
B (bottom bar).
Then insert
C (bottom
bar)
into the opposite side of
F (seat)
.
10. Underneath the seat, insert
L (long screws)
on both outside
holes. One
M (short screw)
will go in the middle hole. Using
both
N (hex wrenches)
tighten screws all the way.
11. Slide
E (handle)
over
D (top bar)
and use reaming
M (short screws)
.
Using both
N (hex wrenches)
tighten screws all the way.
12.
Complete your Hoopla Swing by tying
H (streamers)
through both handles.
INSTALLATION
TREE LIMB OR CROSS BAR ASSEMBLY:
First test
the tree limb or cross bar to ensure that it is secure,
it will support at least 150 lbs., is over level ground,
has a minimum height of 7 feet and is no less than
6 feet on all sides from vertical elements. Swing
should have a clearance of at least 1.5 times the total
length of all the rope measured from the tree limb/
horizontal beam to the tree strap attachment point.
(See Figure: 1)
GENERAL INSTRUCTIONS:
•
DO NOT install home playground
equipment over concrete, asphalt, packed
earth, grass, carpet or any other hard
surface — A fall onto a hard surface can
result in serious injury or death to the
equipment user.
•
To prevent serious injury, equipment must
not be used until properly installed.
Ages
5
+
ADJUST SWING HEIGHT
•
Adjust swing hanging length so platform is parallel with ground. Bottom of swing
should be no more than 24 inches and no less than 18 inches from the ground.
•
Ensure that the swing hangs horizontal after adjustment of the ropes.
•
Never add extra length to chain or rope. The chains or ropes provided are the
maximum length designed for the swinging element(s).
1.
2.
3.
4.
6.
7.
8.
5.
10.
9.
11.
12.
NOTE: Continued on Back Side
