1of2
For Styles SNNL8411K and SNNL8411PN
Please go to
for product cleaning tips. Go to the
selection.
LED 22W
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact your original place of purchase.
www.quoizel.com
Care + Maintenance
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated .
Tools Required:
Light Source:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
STEP 2
Fit Backplate to
Crossbar Assembly
-
A.
on Fixture Body (B) to
the
Remove mounting balls from the
Crossbar Assembly (A). Fit the
backplate
Crossbar Assembly (A) and
secure with mounting balls.
Note: The backplate
should be snug against
the wall and the mounting balls.
If
on Fixture
Body (B)
not, adjust the length of the
mounting screw on the Crossbar
Assembly (A) by unscrewing the
preassembled hex nut and lock
washer and then screwing the
mounting screws in or out of the
crossbar until the correct length
is achieved. Once the backplate
on Fixture Body (B) is secure,
remove the mounting ball and
Fixture Body (B) and proceed to
Step 3.
Figure 2
Mounting
Screw
B
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Figure 4
STEP 4
Install Fixture Body
-
A. Position the backplate and
Fixture Body (B) onto the
Crossbar Assembly (A).
Place the holes in the
backplate over the mounting
screws. Secure the Fixture
Body by using the mounting
balls and hand tighten the
mounting balls until snug.
Figure 5
STEP 5
-
Apply Silicone Sealer
A. Make sure exterior wall surface and
fixture backplate are free of dirt
before applying caulk. Using
exterior grade caulk, caulk over top
of backplate and down other side.
Do not caulk bottom of fixture
backplate to ensure proper moisture
drainage.
Your fixture is now assembled and
ready to use. Enjoy!
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (D) to make all wire connections.
Twist connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Mounting Screw
B
Mounting Ball
A
Backplate
Exterior
Grade
Caulk
Backplate
Installation Guide #IS-SNNL8411
2018 QuoizelInc.
ReleasedDate:2019-08-09
visit us on-line at www.quoizel.com
Package Contents
B
Fixture Body
x 1
STEP 1
Install Crossbar Assembly
-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(C). Tighten until snug
.
Supply Wires
with Ground Wire
Outlet
Box
Figure 1
A
Crossbar
Assembly
x 1
A
Alternate
Mounting
Screw
x 2
E
Outlet Box Screw
x 2
C
Wire Connector
x 3
D
C
