M&G DuraVent DuraStack PRO DAS1 Скачать руководство пользователя

Страница: 1 / 35

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Listed to standards:
UL-103

UL-103HT

ULC-S604

ULC-C959

INSTALLATION AND

MAINTENANCE INSTRUCTIONS

Factory-Built Chimney

• Boiler Stack

• Engine Exhaust

DuraStack PRO

MODELS DCL, DAS1, DIS1, DIS2, DIS4

DCL:

Single Wall

DAS1:

Air Insulated

DIS1, DIS2, DIS4:

A.E.S Refractory wool Insulation

This installation manual will enable you to obtain a safe, efficient

and dependable installation of this chimney system. Please read

and understand these instructions before beginning your installation.

Do not alter or modify the components of this chimney system under any

circumstances. Any modification or alteration of the chimney system

or approved accessories, including but not limited to the appliance

it is connected to, may void the warranty, listings and approvals of

this system and could result in an unsafe and potentially dangerous

installation.

SAVE THESE

INSTRUCTIONS

FOR FUTURE REFERENCE

WARNINGS

FAILURE TO FOLLOW THESE INSTALLATION

INSTRUCTIONS COULD CAUSE FIRE, CARBON

MONOXIDE POISONING, OR DEATH. IF YOU ARE

UNSURE OF INSTALLATION REQUIREMENTS, CALL

THE PHONE NUMBER LISTED ON THE BACK OF

THESE INSTRUCTIONS.

A MAJOR CAUSE OF CHIMNEY RELATED FIRE IS

FAILURE TO MAINTAIN REQUIRED CLEARANCES

(AIR SPACES) TO COMBUSTIBLE MATERIALS. IT

IS OF UTMOST IMPORTANCE THAT THIS GREASE

DUCT BE INSTALLED ONLY IN ACCORDANCE WITH

THESE INSTRUCTIONS.

PIDuraStackPRO REV.00 05/2016

MH10971

Содержание DuraVent DuraStack PRO DAS1




































Результаты поиска

Содержание DuraVent DuraStack PRO DAS1

Отзывы:

Похожие инструкции для DuraVent DuraStack PRO DAS1

Бренды по названию

Популярные бренды

M&G DuraVent DuraStack PRO DAS1, Инструкция по установке и обслуживанию

Результаты поиска

Содержание DuraVent DuraStack PRO DAS1

Отзывы:

Похожие инструкции для DuraVent DuraStack PRO DAS1

Бренды по названию

Популярные бренды