background image

Magnetic Power Systems, Inc.

1626 Manufacturers Drive. Fenton, MO  63026

Tel: 636.343.5550

 Fax: 636.326.0608

 [email protected]

INSTRUCTION MANUAL

DIGITRAC

%%%%

 

2

DIGITAL TENSION READOUT AND CONTROL

TABLE OF CONTENTS

Section

Title

Page

Figure

Title

Page

1

Introduction ........................... 2

Specifications ....................... 20

2

Installation............................. 2

1

Wiring Isolated Inputs .......... 15

3

Electrical Connections .......... 3

2

System Types....................... 16

4

Setup and Calibration ........... 3

3

PA-2 Installation ................... 17

5

PA-2/PA-90 Installation......... 5

4

Wiring Diagrams................... 18

6

Optional Features ................. 6

5

Outline Dimensions .............. 19

7

Trouble Shooting ................ 12

6

Screen Flow Chart................ 21

8

Reset Procedures ............... 15

All of the information herein is the exclusive proprietary property of Magnetic Power Systems, Inc., and is
disclosed with the understanding that it will be retained in confidence and will neither be duplicated nor copied in
whole or in part nor be used for any purpose other than for which disclosed.

Copyright 2002, all rights reserved.

850A154-1
8/02  Rev. D

Summary of Contents for DIGITRAC 2























Reviews: