MACTRAP Grease Boss G25 216 Operational Manual Download | Manualshive

Page: 1 / 9

background image

1

Mactrap Grease Boss Operational Manual v Feb 2017

OPERATIONAL MANUAL

MACTRAP Grease Boss G25 Model -216

Automatic Grease Removal Unit (GRU)

The picture above shows the MACTRAP Grease Boss with

optional

pump out unit at outlet end

Units are right or left hand inlet flow to suit customer location. The above example is left to right flow

Supplied and serviced By:

MACTRAP

For more information contact

MACTRAP

Phone: +64 7 549 0414 / Mobile: +64 274 978 791
Email: [email protected] www.mactrap.co.nz

Manufactured by MACTRAP Katikati New Zealand

1
2
3
...
»

Summary of Contents for Grease Boss G25 216










Reviews:

No comments

Related manuals for Grease Boss G25 216

Elite HydroTap G4 range

Brand: Zip Pages: 20

Brand: Atlas Copco Pages: 40

Brand: Viqua Pages: 23

WATERFRIEND exclusiv MRD-1

Brand: OSF Pages: 44

Brand: vitapur Pages: 36

Brand: Econ Pages: 7

Brand: Neptun Premium Pages: 120

BOFA DentalPRO 250

Brand: Donaldson Pages: 18

Brand: Watts Pages: 20

Brand: ProFlow Pages: 53

Brand: Hans Pages: 65

Brand: Adey Pages: 8

Brand: ACO Haustechnik Pages: 512

Viridian Delta-T

Brand: Taco Pages: 8

Brand: Taco Pages: 8

Brand: SMARDY Pages: 8

Filtobox PXBF06000

Brand: PondXpert Pages: 4

Brand: Pond Boss Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands