background image

 

 

 

 

1/21

 

23.01.2023, Revision 03 

Instruction  for  installation  of  the  Network  Adapter  for 

NANOCOLOR

®

 VIS II and 

UV

/

VIS

 II 

 

 

 

 

 

 

 

Content 

1.

 

Introduction ...................................................................................................................................................................... 2

 

2.

 

Connection setup ............................................................................................................................................................. 2

 

3.

 

Installation of the Network Adapter .................................................................................................................................. 3

 

4.

 

Configuration of the Network Adapter 

– settings .............................................................................................................. 4

 

5.

 

Configuration of the WiFi module ................................................................................................................................... 12

 

6.

 

Configuration of the 

NANOCOLOR

®

 spectrophotometer ............................................................................................... 14

 

7.

 

Errors, Causes and solutions ......................................................................................................................................... 17

 

8.

 

Share network drive ....................................................................................................................................................... 18

 

9.

 

Contact ........................................................................................................................................................................... 21

 

 
 

 

Summary of Contents for 162735






















Reviews: