![background image](http://html1.mh-extra.com/html/lumascape/ls345/ls345_instructions_1947520001.webp)
10-15 MIN.
60
30
45
GIMBAL
LOCKING
SCREW
GIMBAL
ROTATION
LOCKING
SCREW
A
START
HERE
IMPORTANT INSTRUCTIONS
FOR UNDERWATER USE
t
90 C
t
90 C
1m
A.C.N. 010 572 773
1
3
2
7
8
4
6
5
Lumascape Lighting Industries 2006
©
www
.lumascape.com.au
LUMASCAPE
HEAD OFFICE
T 07 3286 2299 F 07 3286 6599
LUMASCAPE
SYDNEY - NSW
T 02 9519 6860 F 02 9519 8834
LUMASCAPE
MELBOURNE - VIC
T 03 9686 1900 F 03 9686 1700
ECC LIGHTING
LUMASCAPE AGENT - NZ
T 09 379 9680 F 09 308 9328
H.I. LIGHTING
LUMASCAPE AGENT - WA
T 08 9321 5422 F 08 9321 5881
NQ LIGHTING
LUMASCAPE AGENT - NTH QLD
T 07 4031 4490 F 07 4031 5933
T 1-(650)-595-LUMA(5862) 1-(650)-595-5820
LUMASCAPE USA INC
Free Call 1-866-695-LUMA(5862)
LIGHTING PARTNERS AUSTRALIA
LUMASCAPE AGENT - SA
T 08 8232 0074 F 08 8232 0076
Lumascape Lighting Industries Pty Ltd
38-44 Enterprise Street, Cleveland, QLD 4163, Australia
PO Box 1875, Cleveland D.C., QLD 4163, Australia
T 07 3286 2299
F 07 3286 6599
E [email protected]
W www.lumascape.com.au
WARNING
DO NOT SHORTEN, INTERFERE OR DISCONNECT CABLE FROM FITTING. WARRANTY WILL BE VOID IF
CABLE ASSEMBLY IS TAMPERED WITH.
If cable damaged replace with cable supplied by LUMASCAPE only.
90
o
Locate Fixtures
Site fixture in proximity to cabling.
Use discretion in locating fixtures as
glass can become very hot and may
burn.
100MM
(3.93IN)
100-250MM
(3.93-9.84IN)
160MM
(6.3IN)
Mount Bracket to Fixture
Mount bracket supplied to fixture using
the M10 dome nuts and washers as
shown
DOME NUT
SPRING
WASHER
FLAT
WASHER
BRACKET
Mount Fixture
Mount fixture to secure surface.
Orientate fixture as required and
tighten nuts
30
o
90
o
BRACKET TOP VIEW
70MM (2.75IN)
2 X 8MM
12MM
30
o
90
o
Insert Lamp
Check lamp WATTAGE, VOLTAGE, and
TYPE, and insert into lampholder (refer to
lamp manufacturers documentation for
handling precautions).
Adjust Gimbal Position.
Adjust the vertical position of the gimbal to
minimise glare, and tighten locking screw.
Rotate gimbal to desired direction and
tighten locking screw.
Test Fixture
Test to ensure fixture is operational. Allow to
burn for 10-15 minutes to allow any
moisture in fixture to evaporate.
C1612US - 2006_07_REV001
Further
information
over page
C1613 - 2007_01_REV-003
Connect Supply
Connect fixture to supply cable according to
local wiring rules.
For Installation LS345: MH, UNDERWATER
1
2
6
5
3
4
Torque Pattern
Seal Fixture
Ensure seal and sealing surface is clean.
Clean glass if necessary. Tighten lid screws
using the 3mm Allen key supplied.
Lumascape recommends tightening in the
above Torque Pattern to 2.5 - 3 N.m.
DO NOT OVER TIGHTEN.
Warning: The Luminaire should only be used complete with its protective shield (cover)
To avoid potential unsafe lamp failure, the luminaire should be switched off at least once a week
DISCONTINUED PRODUCT