background image

4

5

7

8

MI

M2

*

6

I

2

3

BRT  

BRT  

SPEED  

SPEED  

C T

C T

INTRODUCTION

The remote control and receiver combo for Dynamic Tunable White strip lights uses the most advanced RF wireless transmission technology.
The system consists of two parts: the handheld remote control and the in-line receiver.
Featuring a 2-memory and 8-zone programmable remote control, it allows you to quickly adjust brightness and adjust color temperature to create 
a warmer, soothing atmosphere or a cooler one to work by. In addition, it includes a wall mount to easily mount the remote control on a nearby 
wall.
This unit is compatible with any Flexfire LEDs Dynamic Tunable White strip light. 

SAFETY AND WARNINGS

REMOTE CONTROL

Install in accordance with the National Electric Code, and local regulations. 
This product should be installed and serviced by a qualified electrician. 
Do not connect directly to high voltage 120V AC power. 
This product is rated for indoor installation and is not protected against moisture. 
Proper heat dissipation will prolong the working lifespan of this product. Install in a well ventilated area. 
Only install compatible LED power supplies and fixtures. Contact Technical Support or visit the product page for compatible accessories.  
Ensure applicable wire is installed between power supply, fixture, and any controls in between. When choosing wire, factor in voltage drop, 

amperage rating, and type (in-wall rated, wet location rated, etc). Inadequate wire installation could overheat wires and cause fire.  
Utilize the wiring diagrams in this installation guide for basic setups.







Details

DYNAMIC TUNABLE WHITE MULTI-ZONE

LED Remote Control & Receiver

Sync Status Indicator Light

Color Temperature adjust

Zone Selection Buttons

On/Off Button

Memory Buttons

Speed Adjust
Brightness Adjust

SKU:
Working Voltage:
Working Frequency:
PWM Frequency:
Max. Signal Range:
Working Temp:
Dimensions:

Weight:
Warranty:

DYN-MZ-CTRL

5V (Built-in lithium battery)

2.4GHz

2000Hz

98ft (30m)

-22°F ~ 131°F (-30°C ~ 55°C)

H: 5 3/4” (146mm) W: 2 1/4” (56mm) 

D: 7/8” (22mm)*

7oz (200g)

5 years

Touch Adjustable Color Circle

(Keep pressing to adjust brightness 
continuously)

(press for 3 seconds to save the
current settings for future recall)

*Comes with a wall mount for easy storage

V.2018.10.03

DYN-MZ-COMBO

1

page

support@FlexfireLEDs.com

925-273-9080 opt 2

Dynamic Tunable White Multi-Zone Combo

User Guide

Summary of Contents for T2M








Reviews: