ASSEMBLY INSTRUCTIONS
ATTACH BACK
ATTACH LOWER SHELF & BACK PLATE
ATTACH TOP BRACE
ATTACH SEAT BRACE
ATTACH SEAT & BRACE
ATTACH FACE PLATE
ATTACH SEAT SET
ATTACH BACK SET
1
1
3
5
2
2
4
6
*Please read
Assembly Tips
before beginning assembly.
Fit Back edge into Left Side groove track cut out with the pocket cut out in the Back facing
the threaded insert in the Left Side. Place Block B into Back’s pocket cut out and insert bolt
through the block into Left Side threaded hole and finger tighten.
*Please read Assembly Tips before beginning assembly.
Fit edge of Lower Shelf that has holes through it into the groove track cut out of the Back
Plate, and fit both pieces into the groove track cut outs of the Left Side. Place G Blocks into
the Lower Shelf and Back Plates pocket cut outs, insert bolts through the blocks into the Left
Sides threaded holes, and finger tighten
Fit Top Brace edge into Left Side’s pocket cut out. Place G Blocks into the Top Brace’s
pocket cut out, insert a bolt through the block into the Left Side’s threaded holes, and finger
tighten.
*Repeat steps 1-3 to attach Right Side.
Align Seat Brace holes with the holes of the Seat Set, then insert bolts through the Seat
Brace into the Seat Set’s threaded holes and finger tighten.
Fit Seat edge into Left Side groove track cut out so that the groove track cuts in the Seat line
up with the groove track cut outs in the Left Side. Place Block B into Seats pocket cut out,
insert bolts through the block into Left Sides threaded holes, and finger tighten. Fit long edge
of the Seat Brace in the Seats groove track cut out and the short end of the Seat Brace into
the Left Sides pocket cut out.
Fit Face Plate short edge into the Left Side’s pocket cut out. Place G Block into the Face
Plate’s pocket cut out, insert a bolt through the block into the Left Side’s threaded hole, and
finger tighten.
Repeat steps 1 & 2 to attach Right Side.
Layout the Seat Set so that the groove track cut outs line up. Place Seat Set individually over
assembled chair sides (start with A then B and C) by fitting the groove track cut outs with the
Sides and Front Plate. Place G Blocks into the Sides pocket cut outs, insert bolts through the
blocks into the Seat Sets threaded holes, and finger tighten.
Layout the Back Set so that the groove track cut outs line up. Place Back Set individually
over assembled chair sides (start with A then B, C, D) by fitting the groove track cut outs with
the Sides and Front Plate. Place G Blocks into the Sides pocket cut outs, insert bolts through
the blocks into the Back Sets threaded holes, and finger tighten.
*Note: Use same color G Block as Racing Stripe color.
**Using provided wrench securely tighten all bolts.
* It is very important that you finger tighten all bolts into inserts to ensure that you do not cross-thread bolts and inserts before tightening. It
will also be easier if you wait to tighten bolts until you have all bolts installed and the piece completely assembled. This will allow for more
movement of individual pieces and help in aligning holes with inserts. Use the Allen Tool provided to finish tighten bolt until snug.
Step 1
Step 2
Step 3 And repeat on other side
Step 4
Step 5
Step 6
Step 1
Step 2
Step 3 And repeat on other side
Step 4
Step 5
Step 6
Step 1
Step 2
Step 3 And repeat on other side
Step 4
Step 5
Step 6
Step 1
Step 2
Step 3 And repeat on other side
Step 4
Step 5
Step 6
Step 1
Step 2
Step 3 And repeat on other side
Step 4
Step 5
Step 6
Step 1
Step 2
Step 3 And repeat on other side
Step 4
Step 5
Step 6
