background image

P R O D U C T   D A T A   S H E E T

TWINDRIVE

TM

TD1

Features:

•  Angle footrest 45°± 3°
•  Angle headrest 68° ± 3°
•  Compatible with HB10 and HB20
•  EOP in TD1 280 version
•  Toroidal Transformer in TD1 280 and EI core 
  Transformer in TD1 220
•  Duty cycle: 10% ~ 6 min. per hour max. 2 min.
  continuous use followed by 18 min. not in use
•  Max. speed: 0.58 RPM with max. torque
•  Installation dimension:  796 mm length x 90 mm
  height x 90 mm width. Installation dimension 
  on the shaft 581 ± 1 mm
•  Colour: Grey plastic on motor 
  housing RAL 7035, closing 
  device Grey RAL 7016
• Ambient temperature: 
  +5°C to +40°C
• Storage and transport 
 temperature: 
  -10°C to + 70°C
•  Approved according to EN 60335-1
•  EMC according to EN55014 -1 / EN55014 - 2
• Low built-in height
• Low noise level

Options:

•  Emergency lowering (2 x 9V batteries)
• External Mains cut-off
•  Internal mains cut off (only TD1 220)
•  1 extra channels for an extra motor (analogue 
 systems)
•  Up to 2 extra channels for extra motors (only
  TD1 280 with memory and Infrared)
•  Memory (only TD1 280)
•  Memory and Infrared (only TD1 280)
• Black

The TWINDRIVE™ TD1 is a completely new 

product, which is part of the Comfort furniture 

group and has been produced to supply the 

growing demands for motorised systems in the 

leisure bed area. 

TD1 is characterised by the very low built in 

height, which makes it unique in this market 

and gives much more free height under the bed 

than previous systems for e.g. storage or easy 

cleaning access.

Summary of Contents for TWINDRIVE TD1









Reviews: