PK-A3218-10-00-0C
INSTALLATION INSTRUCTIONS
Cat. Nos.
LP3xx-MC, LP4xx-MC
Outdoor Meter - Load Center Combination Enclosure
INSTALLATION
WARNING: TO AVOID FIRE, SHOCK,
OR DEATH: TURN OFF POWER THAT
IS SUPPLYING THIS EQUIPMENT AND
CONFIRM POWER IS OFF
before installing,
removing, or servicing this equipment.
Step 1: Remove meter and wiring
compartment covers
(Figure 1)
.
a.
Remove
meter cover (B)
by loosening
the
securing screw (J)
and sliding cover
down and out.
b.
Remove
wiring compartment cover (C)
by loosening the
securing screw (K)
,
sliding
the
securing latch (A)
upward, and
sliding cover out and down.
c.
Slide the
wiring compartment cover (C)
up and out.
Step 2:
(Optional)
Remove load center door.
NOTE:
The load center door can be removed for
easier installation.
a.
Lift
door (D)
upward to remove from
hinge (E)
(Figure 2)
.
b.
When installation is complete, align the
door
hinge (E)
with the hinge pin and insert
downward until door is seated.
Step 3: Wire bottom feed.
NOTE:
Before removing any knockouts from
the enclosure, consult local electrical codes to
determine the knockout requirements.
a.
To remove
knockouts (F)
, first strike the center
of the knockout.
b.
Pry each
ring (G)
up, one at a time, and grip
both ends with a pair of pliers.
c.
Use pliers to bend the
rings (E)
until they
disconnect from the enclosure
(Figure 3)
.
Step 4: Mount the enclosure.
a.
Remove the
deadfront (S)
by loosening the
securing screw (T)
and lifting the
deadfront
(S)
off the enclsoure
(Figure 9)
.
b.
Remove
mounting knockouts (H)
from the
back of the enclosure
(Figure 4)
.
c.
Use outdoor-approved screws or nails (not
provided) in the
mounting knockouts (H)
to
secure the enclosure to the wall.
Figure 1
Figure 3
Figure 2
Figure 4
a.
b.
c.
IMPORTANT SAFETY INSTRUCTIONS -
READ ALL INSTRUCTIONS BEFORE USING.
LIMITED PRODUCT WARRANTY
For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the warranty, you may call 1-800-323-8920.
WARNINGS
•
TO AVOID FIRE, SHOCK, OR DEATH: TURN OFF POWER THAT IS SUPPLYING THIS EQUIPMENT AND CONFIRM POWER IS OFF
before installing, removing, or servicing this equipment.
• This equipment
MUST BE
installed and serviced by an electrician.
• To be installed and/or used in accordance with electrical codes and regulations.
• Use
ONLY
approved fittings and clamps to avoid damage to wires.
• Leviton
®
circuit breakers
MUST BE
used with a Leviton circuit breaker enclosure.
• Before providing power to the load center, check all electrical connections and confirm that the wiring is correct.
• Replace all doors and covers before connecting power to this equipment.
•
SAVE THESE INSTRUCTIONS.
Knockout
(F)
Ring
(G)
Ring
(E)
Mounting
Knockouts
(H)
Down
Meter Cover
(B)
Wiring
Compartment
Cover (C)
Down
Out
Out
Hinge Pin
Hinge (E)
Door (D)
Securing
Latch (A)
Screw
(K)
Screw
(J)
Meter Cover (B)
Wiring
Compartment
Cover (C)
Patents covering this product, if any, can be found on Leviton.com/patents.
WEB
VERSION
