background image

Page 1

Corp. 0721-L7

XP14

Service Literature

Revised April 7, 2017

INSTALLATION AND SERVICE

PROCEDURE

XP14 (HFC-410A) SERIES UNITS

WARNING

Improper installation, adjustment, alteration, service or
maintenance can cause personal injury, loss of life, or
damage to property.

Installation and service must be performed by a licensed
professional installer (or equivalent) or a service agency.

CAUTION

As with any mechanical equipment, contact with sharp
sheet metal edges can result in personal injury. Take
care while handling this equipment and wear gloves and
protective clothing

.

IMPORTANT

The Clean Air Act of 1990 bans the intentional venting of
refrigerant (CFCs, HCFCs and HFCs) as of July 1, 1992.
Approved methods of recovery, recycling or reclaiming
must be followed. Fines and/or incarceration may be
levied for noncompliance.

TABLE OF CONTENTS

Model Number Identification

2

. . . . . . . . . . . . . . . . . . . .

Typical Serial Number Identification

2

. . . . . . . . . . . . . .

Specifications

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical Data

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unit Dimensions

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unit Parts Arrangement

8

. . . . . . . . . . . . . . . . . . . . . . . .

Operating Gauge Set and Service Valves

10

. . . . . . . . .

Recovering Refrigerant from System

12

. . . . . . . . . . . . .

Unit Placement

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing and Installing Panels

15

. . . . . . . . . . . . . . . . .

New or Replacement Line Set

17

. . . . . . . . . . . . . . . . . . .

Brazing Connections

19

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Flushing Line Set and Indoor Coil

22

. . . . . . . . . . . . . . . .

Installing Indoor Metering Device

23

. . . . . . . . . . . . . . . .

Leak Test Line Set and Indoor Coil

24

. . . . . . . . . . . . . . .

Evacuating Line Set and Indoor Coil

25

. . . . . . . . . . . . .

Electrical

26

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Servicing Units Void of Charge

27

. . . . . . . . . . . . . . . . . .

Unit Start-Up

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Refrigerant

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Operation (XP14-XXX-230-01 through 07)

34

.

Defrost System (XP14-XXX-230-01 through 07)

36

. . .

System Operation (XP14-XXX-230-08 and later)

34

. . .

Defrost System (XP14-XXX-230-08 and later)

36

. . . . .

Maintenance

42

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Start-up and Performance Checklist

47

. . . . . . . . . . . . .

Unit Wiring Diagram and Sequence of 
Operations

43

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The XP14 is a high efficiency residential split-system heat
pump unit, which features a scroll compressor and
HFC-410A refrigerant. XP14 units are available in sizes
ranging from 1-1/2 through 5 tons. The series is designed
for use with an indoor unit with an check expansion valve
approved for HFC-410A.

 

IMPORTANT

This unit must be matched with an indoor coil as
specified in 

Lennox XP14

  E

ngineering Handbook

.

Coils previously charged with HCFC-22 must be
flushed.

Summary of Contents for XP14-018-230-01



















































Reviews: