Lennox 11U61 Setup And Installation Manual Download

Page: 1 / 35

201

Lennox Industries Inc.

Dallas, Texas, USA

THIS MANUAL MUST BE LEFT WITH THE HOMEOWNER

FOR FUTURE REFERENCE

NOTICE

Read this manual before programming this thermostat.

Use this thermostat only as described in this manual.

WARNING

Improper installation, adjustment, alteration, service or maintenance
can cause property damage, personal injury or loss of life.

Installation and service must be performed by a licensed professional
HVAC installer (or equivalent) or service agency.

INSTALLER'S SYSTEM SETUP
GUIDE

iComfort Wi-Fi

Flex

Touchscreen Programmable Thermostat (11U61)

CONTROLS

Shipping and Packing List

Thermostat container includes:

1 - Thermostat

4 - Wall anchors

1 - Homeowner's manual

4 - Mounting screws

Equipment Interface container includes:

1 - Equipment Interface Module

1 - Equipment Interface Module Installation Instruction

1 - Warranty card

Summary of Contents for 11U61




































Search results

Summary of Contents for 11U61

Reviews:

Related manuals for 11U61

Brands by name

Popular brands

Lennox 11U61, Setup And Installation Manual

Search results

Summary of Contents for 11U61

Reviews:

Related manuals for 11U61

Brands by name

Popular brands