1/16
LEGRAND - BP30076
87045 LIMOGES CEDEX FRANCE
Telephone: 05 55 06 87 87
–
Fax: 05 55 06 88 88
ELIOT Kit STOP&GO Connected
Cat. N°: 4
149 54
CONTENTS
PAGE
1. Description - Use................................. 1
2. Product range ..................................... 1
3. Overall dimensions .............................. 1
4. Preparation - Connection .................... 2
5. General characteristics........................ 8
6. System architecture .......................... 12
7. Conformities and approvals ............... 13
8. Auxiliaries and accessories ............... 14
9. Application messages ....................... 15
1. DESCRIPTION - USE
Device dedicated to guarantee service continuity.
Via the app
“
POWER ON
”
(available for free on Google Play and
Play Store), gives to the user information on the status of the
associated circuit (open/ closed/ tripped ...).
In case of unwanted tripping (temporarily electrical disturbances or
other external events) and if no permanent fault is detected: it sends
a notification to user in order to get an authorization to remotely
switch ON the associated device.
In case of permanent fault: the user will be informed about it without
having the possibility to remotely switch on the power, to guarantee
total security.
The associated circuit must be protected by a 1 module per pole
DX
3
RCCB or RCBO up to 63 A.
(not delivered with the kit).
2. RANGE
. Cat. n° 4 149 54: Eliot Kit Stop&Go Connected, composed by:
Non-automatic resetting Stop and go (cat. no 4 149 54)
. During a “normal situation”:
- It permanently checks the status of the installation.
- It gives remotely a series of information to the user: circuit
open/closed, manually open/closed, ...
. Following
an “unwanted tripping” due to a
non-permanent fault:
- It reports the information through the Smartphone app
- Allows the user to remotely switch it ON
- In case of recurrent non-permanent faults, the Stop&Go will not
allow some remote command
(see details on page 5)
. Following
an “unwanted tripping” due to a permanent fault (earth
leakage or short circuit):
- It reports the information through the Smartphone app
- It does not allow the use to remotely switch-On the device and
advises to contact an electrician to check the installation.
. Technology: DC electric motor with permanent magnets
. 2 modules (35,6 mm) width
. Rated Voltage & Frequency: 230 V ~ 50 / 60 Hz with standard
tolerances.
. Operating voltages:
Minimum (0,85 x Un): 195,5 V
Maximum (1,1 x Un): 253 V
2. RANGE
(continued)
Wi-Fi interface module (cat. no 4 149 52)
To communicate with the Smartphone through a Wi-Fi Box
. 1 module (17,8 mm) width
. Supplied by the Power supply module via supply patch cord
. Equipped with a 1m length pre-cabled cable to connect with the
Stop&Go
Power Supplier Module for the Wi-Fi interface (cat. no 4 149 45)
. Primary voltage 95÷250 V~
. Secondary voltage 12 VDC 500 mA
. 1 module (17,8 mm) width
Supply patch cord:
. Allows to connect the Power supply module with the Wi-Fi interface
at the downstream through dedicated connectors.
. Length: 250 mm
Configuration & use:
. Must be used with the app “POWER ON”
. To be downloaded for free on Google Play or Play Store
All the configurations steps are explained in the app.
Note: This part can be done without any ADSL Wi-Fi box thanks to
the Wi-Fi module which allows to display its own network for this
step.
3. OVERALL DIMENSIONS
. Stop&Go
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016
