Labom PASCAL CS21 0 Series Operating Instructions Manual Download

Page: 1 / 20

Pressure transmitter PASCAL CS

Type series CS21x0

Questions about this device? H49 (0) 4408 804 - 444

LABOM Mess- und Regeltechnik GmbH Im Gewerbepark 13 27798 Hude Deutschland

Tel.: +49 (0) 4408 804-0 Fax: +49 (0) 4408 804-100 e-mail: [email protected] www.labom.com

BA_060

Rev 1B6

Page 1/20

Operating Instructions

General Information....................................................................................................... 2

1.1

General Safety Notes .............................................................................................. 2

1.2

Intended Use ........................................................................................................... 2

1.3

Conformity with EU Regulations .............................................................................. 2

Transportation and Storage .......................................................................................... 2

Installation and Commissioning .................................................................................. 2

3.1

Mechanical Installation ............................................................................................ 2

3.2

Electrical Connection .............................................................................................. 3

3.3

Adjusting the Display Unit ....................................................................................... 4

3.4

Devices with Diaphragm Seal ................................................................................. 5

Operation ........................................................................................................................ 5

4.1

Setup / Parameterization ......................................................................................... 5

4.2

Maintenance / Service ............................................................................................. 5

Disassembly ................................................................................................................... 6

User Manual ................................................................................................................... 7

6.1

System Operating Principles ................................................................................... 7

6.2

Main Menue .......................................................................................................... 11

6.3

Basic Menue (

bASE

) ............................................................................................. 11

6.4

Display Menue (

diSP

) .......................................................................................... 14

6.5

Switch-point Menue (

) ....................................................................................... 15

6.6

System Menue (

SYS

) ............................................................................................ 18

6.7

Overview of the Menue Tree ................................................................................. 20

Summary of Contents for PASCAL CS21 0 Series





















Search results

Summary of Contents for PASCAL CS21 0 Series

Reviews:

Related manuals for PASCAL CS21 0 Series

Brands by name

Popular brands

Labom PASCAL CS21 0 Series, Operating Instructions Manual

Search results

Summary of Contents for PASCAL CS21 0 Series

Reviews:

Related manuals for PASCAL CS21 0 Series

Brands by name

Popular brands