background image

3. Product Description

Description and function

LED Type: 
KNC-VNi100HD, KNC-VNi120HD

Standard Type: 
KNC-VDi100HD, KNC-VDi120HD

1. Infrared LED – These LEDs emit infra red radiations. 
2. Cooling fan – Cools the components and prevents them from overheating. 
3. Service Video Connector – 
Outputs video to the monitor.
4. Reset Button – Resets the product to the factory default settings.
5. Power Input(DC12V) – Connect DC 12V power.
6. Digital Input – Connect signal from external sensor.
7. Digital Output – Connect signal to external alarm. (Max. current - DC 12V, 70mA)

8. Network Connector – 
The Network Camera connects to the network via a standard network cable, and 
automatically detects the speed of the local network segment
(10BaseT/100BaseTX Ethernet). PoE Supported

3-Axis Gimbal

M121-VDi100/120HD-001

Megapixel Network Camera

KNC-VDi100HD/KNC-VNi100HD
KNC-VDi120HD/KNC-VNi120HD

Installation Guide

Table of Contents

1.INTRODUCTION

2.PACKAGE CONTENTS

3.PRODUCT DESCRIPTION

4.INSTALL THE HARDWARE

5.ASSIGN AN IP ADDRESS

6.TERMINAL BLOCK CONNECTORS

1. Introduction

KNC-VDi100HD,KNC-VNi100HD,KNC-VDi120HD,KNC-VNi120HD Installation Guide

This  installation  guide  provides  instructions  for  installing  the  Network  Camera  on  your 
network.  For  all  other  aspects  of  using  the  product,  please  see  the  User’s  Manual, 
available on the CD included in this package, or from http://www.ktnc.co.kr

Installation steps

1. Check the package contents against the list below.
2. Product description.
3. Install the hardware.
4. Set an IP address.
5. Set the admin and user ID and password, See User’s Manual.

I m p o r t a n t !

This product must be used in compliance with local laws and regulations.

2. Package Contents

Network Camera

Video Output Test Cable

Software CD

Installation Guide

Template

Screws / Plastic anchors /

Wrench / RJ45 Coupler

4. Install the hardware

KNC-VDi100HD, KNC-VNi100HD, KNC-VDi120HD, KNC-VNi120HD are designed to be installed using 
a template as shown below. 

1. Template – To mount the camera.
2. Plastic Anchors(3ea) – To secure the camera to 
                                         the template.
3. Screws(3ea) - To secure the camera to the template.
4. Screws(3ea) – Screws to secure the camera case

Connection

1. Connect the camera to the network using a UTP cable (CAT.5), Power can be supplied via 
    the network cable (PoE)
2. Connect DC 12V to the power terminal. This is not necessary if the Network Camera is 
    connected to PoE hub or midspan.
3. Check that the indicator LEDs indicates the correct conditions.
4. Connect the analog monitor to the service video connector for adjusting focus and press and quickly 
    release the reset switch for focus assistant mode. 
    Then you can select normal view or focus view mode using the reset switch.

Caution: When you use focus assistant mode, “Focus View” mode is recommended for more exact focus.
Caution: Focus assistant mode will be automatically exited after 3 minutes for normal operation.

Dimensions

When using Wall Mount Bracket

Digital Input 

Digital Output 

Pan Rotation

Horizontal Rotation

Tilt Rotation

Ø112.8

Ø151

Ø107

123.4

71.5

Ø124

CAUTION 

panning(Pan + Horizontal) the bracket in excess of 1 rotations in one direction
may cause damage to the cable.

70

˚

70

˚

Tilting angle

When using the camera 

without LED take off the rubber.

N O T E

Lens Zoom Knob

Lens Focus Knob

Reviews: