background image

ã

, 2004

Copyright Kohler China Ltd., 2004

C

1

1023725-T01-A

NOTES

!

!

!

!

!

!

!

!

Observe all local plumbing and building codes.

Carefully plan the moving of the bath into the
installation area. This bath is heavy and will not
easily fit through doorways.
Unpack and inspect the bath for damage. Return the
bath to the carton until you are ready to install.
Provide properly dimensioned framing.
Install the bath to an adequately supported, level
subfloor.
These instructions are for both freestanding and
drop-in installations. Follow only the instructions that
apply to your particular installation.
Before installation, ensure proper access to the final
plumbing connections.
This bath conforms to ANSI Standard A112.19.1. All
dimensions are nominal.

CAUTION: Risk of personal injury.

CAUTION: Risk of product or property
damage.

NOTICE: Make sure the floor will support 2000 lbs.
(907kg).

Cast iron

baths are extremely heavy. Obtain sufficient help
to carefully lift or move the bath.

Do not support the bath by the rim.

Provide adequate support under the feet.

This is the combined weight of the bath, water,

and two bathers.

!

2000

(907

)

ANSI

A112.19.1

!

!

!

!

!

!
!

BEFORE YOU BEGIN

BEFORE YOU BEGIN

368

201419

·

·

·

·

Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. Reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-

We appreciate your commitment to Kohler quality.
Please take a few minutes to review this manual
before you start installation. If you encounter any
installation or performance problems, please don

,

t

hesitate tocontact us. Our phone numbers and
website are listed on the back cover. Thanks again
for choosing KohlerCompany.

please leave these

instructions for the consumer.

·

!

!

!

.

.

DROP-IN OR FREESTANDING CAST IRON BATH

INSTALLATION INSTRUCTIONS

K-700T

VINTAGE

Summary of Contents for Vintage K-700T













Reviews: