1. Select a dry, level site and clear
the ground of any sharp objects.
Remove the tent, pegs and pump
from the carry bag. Untie fabric
ties and unroll tent with the floor
facing down.
2. Spread out the tent and peg out
the four main corners ensuring
the tent is pulled taut and square.
Peg out the middle pegging
points and then the remaining
pegging points on the floor. To
make sure the tent stays in place,
insert the pegs into the ground at
a 45° angle. It is recommended
to pitch the tent so it is in line with
wind, never side on.
3. Unzip and open the doors to
make erecting the tent easier.
4. There is an external valve
located on each air tube. Before
inflating, the valves need to be
screwed into the air tube.
Moa 12 Air Canvas Tent
Model No. KC070-270
Your tent includes:
1 x canvas tent (with air poles attached)
1 x canvas fly (with guy ropes and fasteners attached)
63 x steel pegs
1 x hand pump
5 x steel porch FRAME poles (1 x 22mm top arch, 2 x 25mm corner arches,
2 x 22mm straight poles)
1 x steel porch pole RIDGE (2800mm x 22/25mm)
2 x steel SIDE porch poles (1940mm x 19/22mm)
PITCHING INSTRUCTIONS
Unscrew the valve cap on top of the
valve. Insert the pump hose into the
valve and inflate the air tubes from
the centre tubes outwards. You may
need to help the tube stand up so
it inflates evenly and in the correct
shape. Make sure you only inflate to
the recommended pressure (6-8psi) as
over-inflation can lead to tube damage.
Replace top cap of the valve after
inflating each air tube.
5. It is recommended in hot weather that 6psi is used to allow
for the air to expand inside the air tubes. In cooler/windier
conditions 8psi is recommended. Please adjust the pressure
in the air tubes as the ambient temperature changes. Only use
the pump provided as it has a pressure gauge which shows the
recommended pressure (psi).
6. Make sure the tent is sitting evenly. You may need to adjust the
base of each air pole so it sits flat with the ground.
7. Rope out the guy ropes and fine tune the tent so it remains taut
and positioned correctly. Fold the porch off the roof.
8. Carefully pull the FLY over the tent. Secure the fly to the tent
by fastening the buckles on each corner first, then fasten and
tighten the remaining buckles.
9. Finally, peg out the black webbing straps, ensuring that
adequate tension has been applied to the rope adjusters to keep
the fly sitting securely. Ropes should not be too close to the tent,
ie. more angle means more tension.
10. Assemble all the porch poles. Installation of these poles
will require two people. Fit the porch roof RIDGE pole by
connecting to plastic lug at the tent end. Extend the pole out to
the length of the porch. Support ridge pole at the opposite end
while arched front porch FRAME is being fitted.
11. Fit the arched porch frame under the roof ridge pole and feed
pins through the eyelets at the front of the porch. Extend all
poles out until porch roof and front frame is taut. Secure frame
to the porch with hook and loop tabs.
12. Finish by installing SIDE poles and pegging out guy ropes. When
pegging out the steel porch poles, make sure the ropes are at a
45° angle to apply an even tension.
13. Please read the care instructions for more product information
about your tent.
Filename: 5040_KC070-270_Moa 12 Air_Instr
Dimensions: 400mm W x 200mm H
Colour: Black
PACKING INSTRUCTIONS
REVERSE THE PROCEDURE TO LOWER THE TENT
Take down the porch poles, unzip any doors & windows and remove
the fly. Fold the dry fly and roll until it fits into the fly bag. Remove
pegs, leaving only the four corner pegs. Now deflate the air tubes
in the reverse order shown in the diagram. Unscrew the valve caps
releasing the air in the side air tubes. Make sure all the air escapes
and the doors are unzipped. Once the tent is deflated, remove the
corner pegs. Fold the tent as shown below. Ensure that the air valves
are not obstructed to allow the remaining air to escape. To reduce the
chance of valve malfunction, the valves should be fully unscrewed
when the product is in storage.
Ensure the tent is completely dry and clean before storing away and
store it in a dry environment.
1
2
3
4
5
To keep the porch clean and
out of the way, fold it back
over the roof of the tent until
needed.
Fold porch
onto roof
Fold in side
rooms
Fold into thirds
Valves
this side
Valves
this side
Roll
